5. An angle bracket ABC is restrained by a high- strength steel wire CD, and it supports a load P at A, as shown in Figure. The strength properties of the wire and the shear pin at B are a, = 350 MPa (wire), and t= 300 MPa (pin at B).If the wire and pin are to be sized to provide a factor of safety against yielding of the wire of 3.3 and a factor of safety against ultimate shear failure of the pin of 3.5, what are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)? 90 mm 15° 100 mm View a-a of B P= I kN

5. An angle bracket ABC is restrained by a high- strength steel wire CD, and it supports a load P at A, as shown in Figure. The strength properties of the wire and the shear pin at B are a, = 350 MPa (wire), and t= 300 MPa (pin at B).If the wire and pin are to be sized to provide a factor of safety against yielding of the wire of 3.3 and a factor of safety against ultimate shear failure of the pin of 3.5, what are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)? 90 mm 15° 100 mm View a-a of B P= I kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.4.16P: A rigid bar of weight W = SOO N hangs from three equally spaced vertical wines( length L = 150 mm,...

See similar textbooks

Similar questions

A copper bar AB with a length 25 in. and diameter 2 in. is placed in position at room temperature with a gap of 0.008 in. between end A and a rigid restraint (see figure). The bar is supported at end B by an elastic spring with a spring constant k= 1.2 × 106 lb/in. (a) Calculate the axial compressive stress crcin the bar if the temperature of the bar only rises 50 F. (For copper, use a = 9.6 × 10-6/ and E = 16 × 106 psi.) (b) What is the force in the spring? (Neglect gravity effects.) (c) Repeat part (a) if k ? 8.
A long, rectangular copper bar under a tensile load P hangs from a pin that is supported by two steel posts (see figure). The copper bar has a length of 2.0 m, a cross-sectional area of4S00 mm", and a modulus of elasticity Ec= 120 GPa. Each steel post has a height of 0.5 m, a cross-sectional area of 4500 mm2, and a modulus of elasticity E = 200 GRa. (a) Determine the downward displacement
The assembly shown in the figure consists of a brass core (diameter d:= 0.25 in.) surrounded by a steel shell {inner diameter d2= 0.23 in., outer diameter di= 0.35 in.}. A load .P compresses the core and shell that both have a length L = 4.0 in. The module of elasticity of the brass and steel are Eb=15 X 10fi psi and Es= 30 X 10fi psi, respectively. (a) What load P will compress the assembly by 0.003 in? (b) IF the allowable stress in the steel is 22 ksi and the allowable stress in the brass is 16 ksi. what is the allowable compressive load Pallow? (Suggestion: Use the equations derived in Example 2-8.)
A horizontal rigid bar ABC is pinned at end A and supported by two cables at points B and C. A vertical load P = 10 kN acts at end C of the bar. The two cables are made of steel with a modulus elasticity E = 200 GPa and have the same cross-sectional area. Calculate the minimum cross-sectional area of each cable if the yield stress of the cable is 400 MPa and the factor of safely is 2.0. Consider load P only; ignore the weight of bar ABC and the cables.
A long, slender bar in the shape of a right circular cone with length L and base diameter d hangs vertically under the action of its own weight (see figure). The weight of the cone is W and the modulus of elasticity of the material is E. Derive a formula for the increase S in the length of the bar due to its own weight. (Assume that the angle of taper of the cone is small.)
The roof over a concourse at an airport is supported by the use of pretensioned cables. At a typical joint in the roof structure, a strut AB is compressed by the action of tensile forces Fin a cable that makes an angle = 75° with the strut (see figure and photo). The strut is a circular tube of steel (E = 30,000 ksi) with outer diameter d2= 2.5 in. and inner diameter d1= 2.0 in. The strut is 5.75 ft long and is assumed to be pin-connected at both ends. Using a factor of safety n = 2.5 with respect to the critical load, determine the allowable force F in the cable.
A bracket ABCD having a hollow circular cross section consists of a vertical arm AB{L = 6 ft), a horizontal arm BC parallel to the v0 axis, and a horizontal arm CD parallel to the -0 axis (see figure). The arms BC and CD have lengths b}= 3.6 ft and b2= 2,2 ft, respectively. The outer and inner diameters of the bracket are d-, = 7,5 in. and dx= 6,8 in. An inclined load P = 2200 lb acts at point D along line DH. Determine the maximum tensile, compressive, and shear stresses in the vertical arm
The nonprismalic cantilever circular bar shown has an internal cylindrical hole of diameter dtl From 0 to x so the net area of the cross section n for segment I is A. Load P is applied at x, and load Ptl is applied at x = L. Assume that E is constant. (a) Find reaction force Ry (b) Find internal axial forces Ntin segments I and 2. (c} Find .v required to obtain axial displacement at joint 3 of
A vertical pole of aluminum is fixed at the base and pulled at the top by a cable having a tensile force T(see figure). The cable is attached at the outer edge of a stiffened cover plate on top of the pole and makes an angle a = 20° at the point of attachment. The pole has length a = 2.5 m and a hollow circular cross section with an outer diameter d2= 280 mm and inner diameter d1= 220 mm. The circular cover plate has diameter 1.5d2 Determine the allowable tensile force Tallow in the cable if the allowable compressive stress in the aluminum pole is 90 MPa.
Around brass bar of a diameter d1= 20mm has upset ends each with a diameter d2= 26 mm (see figure). The lengths of the segments of the bar are L1= 0.3 m and L2= 0.1 m. Quarter-circular fillets are used at the shoulders of the bar, and the modulus of elasticity of the brass is E = 100 GPa. If the bar lengthens by 0.12 mm under a tensile load P, what is the maximum stress ??maxin the bar?
A solid steel bar of a diameter d1= 60 mm has a hole of a diameter d2= 32 mm drilled through it (see figure). A steel pin or a diameter d2passes through the hole and is attached to supports. Determine the maximum permissible tensile load P allow in the bar if the yield stress for shear in the pin is ty= 120 MPa, the yield stress for tension in the bar is ??y= 250 MPa, and a factor of safety of 2.0 with respect to yielding is required. Hint: Use the formulas of Case 15, Appendix E.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?