Shown below are two trolleys connected by linear springs. Use the principle of minimum total potential energy to find the forces in the springs and then check that the trolleys are in equilibrium. There is no force in the springs prior to the application of the loads. a 30 kN/mm 400 KN b 20 kN/mm 200 KN OO с 10 kN/mm www 4 d

Shown below are two trolleys connected by linear springs. Use the principle of minimum total potential energy to find the forces in the springs and then check that the trolleys are in equilibrium. There is no force in the springs prior to the application of the loads. a 30 kN/mm 400 KN b 20 kN/mm 200 KN OO с 10 kN/mm www 4 d

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The controlling force curves P, Q and R for a spring controlled governor are shown in the figure, where r₁ and r₂ are any two radii of rotation. Controlling force R 12 11 Radius of rotation The characteristics shown by the curves are AP-Unstable; Q - Stable; R - Isochronous BP - Unstable; Q - Isochronous; R - Stable CP- Stable; Q - Isochronous; R - Unstable DP-Stable; Q - Unstable; R - Isochronous
Q1 The frame structure shown below is in static equilibrium. Find the forces acting at pins C and D. The radius of the freely-rotating pulley is 2 feet. Enter the magnitude of the vertical component of the force at pin C (in lb) in the RESPONDUS answer box. 19:4 100 lb ന Do * **** താൽ | 4 ft A 2 4 ft * 5 ft 34 13 ft | 4t CE D F amo G 3:4
F1 F2 a F3 A d. F4 Consider the following values: - F5 a = 13 m; b = 8 m; c = 10 m; d = 5 m; F1 = 3 kN; F2 = 11 kN; F3 = 2 kN; F4 = 20 kN; F5 =2 kN; a = 30° e = 60° B = 30°
Solve the following system of equations for forces BC and 3 m 3 m -4 m→-4 m→- 4 m- 1.75 kN 2 kN 1.5 kN 2 kN F 1 kN 0.75 kN G 6 m B H C E -6 m- – 6 m - - 6 m- 0=7.83 4.5 +BC -2-BD 4.5 2.8 0=7.83 -BC –BD 2.8 4.5 4.5
An ideal spring, with a pointer attached to its end, hangs next to a scale. With a 100 N weight attached, the pointer indicates "40" on the scale as shown. Using a 200N weight instead results in "60" on the scale. Using an unknown weight X results in "30" on the scale. The weight X is: Hint: Draw the force - Displacement diagram. 100 N O 1.20 N O 2.30 N O 3.40 N O 4.50 N O 5.70 N
STATIC I need the answer within 1 hour. Thanks Using the knot method, find the force that each element in the truss system carries. Indicate whether these elements are under tensile force or under compression force. F1(N)=11 , F2(N)=23
Two weights are hung over two frictionless pulleys that are connected by a wire rope to a 500 Ib horizontal block that are in between and below them. The wire rope attached to the upper left end of the block and to the left pulley is at 45 degrees with the horizontal and the wire rope that connects the upper right end of the block to the right pulley is at 30 degrees with the horizontal. If the weight on the left pulley is 50 lb, fs= 0.30 and fk = 0.20 on the surface of block what weight W on the right pulley will cause the 500 lb block to just start moving to the right? *
A statically determinate truss is one of the early problems addressed in sophomore statics classes. A typical problem is shown in figure below: 2 Fapplied √30° F₁ F3 F2 02 3 L. Hinge Roller The applied force has a magnitude of 1000 N at an angle of 30° from the horizontal, as shown in the figure. The inner angles ₁ and 2 are 45° and 65° respectively. Determine the values of the forces in each member of the truss, and the reactive forces experienced at the hinge and the roller (nodes 2 and 3). Set up the problem using a simultaneous equation system. Use the method of the inverse matrix taught in the lectures. Follow the steps a) to e) as indicated below (assume "S" as the matrix representing the previous system. a) Calculate the matrix of minors of S. b) Calculate the matrix of cofactors of S (name it H) c) Calculate the determinant of S. d) Calculate the Adjoint of matrix of S using adj S = HT e) Calculate the inverse of matrix S using S₁ = adj S/|S|
6 نقاط For the cables shown in the figure, find the forces in each cable if cable C pass over a pulley and holding mass (10kg) pulley 45 C_ 45° 60° 15 B 30 10 kg
h a = 1.25 A NB NA 1223.64 = one A Determine normal forces at A and B. da -1281.63 You are forced to pull a group of kindergarteners in a cart. You apply a horizontal force of F = 500 cart has a total mass of m = 400 kg with a center of mass at G. Assume the wheels have negligible negligible size (r) and no rolling resistance. d4 = 1.28 m and dp = 0.66 m. You apply the horizont at a height y = 0.7 m from the ground. The center of gravity G is located at a height h = 0.8 m from ground. Determine acceleration of the cart m G XN dB X N B F y UBC Engineering
Q1: In the Figure 1, two forces (P & Q) are acting on the same fixed point A. Find the resultant of these forces and its angle with the horizon by using: (a) Graphical solution. (b) Trigonometric solution. Q = 60 N Figure 1: P 40 N 35 Q2: A block of 15 kg was place on an inclined surface as shown in Figure 2. If the static coefficient of friction between the block and the surface is 0.3, find: (a) the maximum friction force. (b) the equilibrium state of the block. 15 kg Figure 2: 30
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure. The horizontal steel beam had a mass of 86.80 kg per meter of length, and the tension in the cable was T = 12170 N. The crane was rated for a maximum load of 500 kg. The acceleration due to gravity is g = 9.810 m/s². If d = 6.160 m, s = 0.450 m, x = 1.500 m, and h = 1.980 m, what was the magnitude of W₁ (the load on the crane) before the collapse? What was the magnitude of force Fp at the attachment point P? WL = Fp = P 0 W₁ N N