Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 9 mm in diameter. Assume a = 550 mm, b = 300 mm, h = 450 mm, P = 900 N, and 0 = 60°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod = (b) Tpin B = (c) Tpin A = (1) tel tel a i i B MPa MPa MPa

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 9 mm in diameter. Assume a = 550 mm, b = 300 mm, h = 450 mm, P = 900 N, and 0 = 60°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod = (b) Tpin B = (c) Tpin A = (1) tel tel a i i B MPa MPa MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please include all solutions.
(c) The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. ----|--²--| A 9 DAB T L P Fig. Q1(c) PL Hint: S = note that ABC is a rigid bar. EA C
Stress Analysis of Trusses using method of sections. pls answer within 30 mins
Given is a truss structure: Where: Working shear stress for the rivets is 70 MPa Working bearing stress due to rivets is 140 Mpa Thickness of the member is 5 mm Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 kN 120 kN B. 3 m E 200 kN 4 Panels @ 4 m = 16 m
Which of the following statements is correct about the given structure? A В C E pin fixed roller fixed It is a determinate structure. O It is indeterminate to 4 degrees. It is indeterminate to 5 degrees. O It is indeterminate to 3 degrees .
TRY THIS ONE ON YOUR OWN!! Assignment 1-M The butt joint shown in the figure is connected using five 20 mm diameter bolt. If the tension force (P) acting on the member is 25 KN, determine the maximum shearing stress developed within among the bolts. Strap Plate Member Plate → P > P
Mechanics. help asap pls
Determine the tensions in cables AB, AC, and AD. B Answers: TAB= TAC = TAD = i i i 2.3 1.45 m 180 kg D 2.20 m 1.30 m 0.40 m N N N
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE
The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.
Please Asap
Which of the following statements is correct about the given structure? A В D E r pin fixed roller fixed It is a determinate structure. It is indeterminate to 4 degrees. It is indeterminate to 5 degrees. It is indeterminate to 3 degrees.