Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 8 mm in diameter. Assume a = 675 mm, b = 350 mm, h = 475 mm, P = 725 N, and 0 = 60°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 8 mm in diameter. Assume a = 675 mm, b = 350 mm, h = 475 mm, P = 725 N, and 0 = 60°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bridge is pinned at A and has a roller at G. A downward load of 12.5 lb is applied at point C, and a downward load of 25 lb is applied at E. The support reactions at the pin and roller are shown on the image. Find the stress in members making up the bridge using either the method of joints or method of sections.
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
Use the subsne member to make a compieneanlyss of e comples uss shown 25kN d 3m 25KN 4 m e1.5 m 2 at 4 m = 8 m
(c) The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. ----|--²--| A 9 DAB T L P Fig. Q1(c) PL Hint: S = note that ABC is a rigid bar. EA C
Problem 1 Classify each of the structures as statically determinate or indeterminate. If indeterminate, specify the degree of indeterminacy. pin rocker fixed 7 pin roller fixed fixed pin roller pin (d) (h) pin fixed Page fixed
TRY THIS ONE ON YOUR OWN!! Assignment 1-M The butt joint shown in the figure is connected using five 20 mm diameter bolt. If the tension force (P) acting on the member is 25 KN, determine the maximum shearing stress developed within among the bolts. Strap Plate Member Plate → P > P
Mechanics. help asap pls
Determine the tensions in cables AB, AC, and AD. B Answers: TAB= TAC = TAD = i i i 2.3 1.45 m 180 kg D 2.20 m 1.30 m 0.40 m N N N
Problem 8: Determine the location ỹ of the centroidal axis i – i of the beam's cross-sectional area. Neglect the size of the corner welds at A and B for the calculation. -150 mm 15 mm B 150 mm -15 mm 50 mm
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE
Three wires (indicated by arrows) act on the connector in the figure. Replace the forces at point A with an equivalent force-force pair system.
Which of the following statements is correct about the given structure? A В D E r pin fixed roller fixed It is a determinate structure. It is indeterminate to 4 degrees. It is indeterminate to 5 degrees. It is indeterminate to 3 degrees.