Replace the loading on the frame by a single resultant force. Specify where its line of action intersects a horizontal line along member CB, measured from end C. Note: Use the last digit of your SR-Code to identify the second digit of F2. For example, 19-01231, the magnitude of the force is 910 N. CE -1 m F3 610 N F4 = 375 N 0.5 m 1.5 m 1 m B [0.5 m 3 F₂=9_0 N F₁ = 425 N -X

Replace the loading on the frame by a single resultant force. Specify where its line of action intersects a horizontal line along member CB, measured from end C. Note: Use the last digit of your SR-Code to identify the second digit of F2. For example, 19-01231, the magnitude of the force is 910 N. CE -1 m F3 610 N F4 = 375 N 0.5 m 1.5 m 1 m B [0.5 m 3 F₂=9_0 N F₁ = 425 N -X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ Two Forces Shown in Fig. (1) acts on the bracket, determine the effect of these two forces (using Parallelogram method). 100 F₂ = 150N F₁ - 200 N
Figure F= Value Submit Request Answer Units A < Return to Assignment Provide Feedback 4 m 30° Determine the magnitude of the projection of force F=680 N along the u axis (Eigure 1) Express your answer to three significant figures and include the appropriate units. U1 4 m 2m < -y F 1 of 1
Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L 8 ft and F 12 lb, Part 2 of 6 NOTE: This is a multi-part question, Once an answer is submitted, you will be unable to return to this part. 10 points y eBook B T 30° Hint F Print References T BA : the position vector from B to A. Mc Graw Hill MacBook Air
ASAP
The figure below shows a steel structure made up of two pre-assembled segments that are hoisted by a mobile crane using a bespoke lifting frame. Each cable must withstand loads of FAB = FAC = FAD = FAE = 4000 kN. You must provide an accurate answer in scientific standard form with one decimal place only. In cartesian vector and in scalar form, compute the rAB, rAC, TAD & rAE length. 14 m 6m 6 m в 3 m 3 m X
S00 Ib In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R = 35 (19-20) the angle of the R measured 500 lb cW from the x- axis.
Q1/ Two Forces Shown in Fig. (1) acts on the bracket, determine the effect of these two forces (using Parallelogram method). 100 F-150N F₁-200 N Fig. (1)
Answer for the 1st part of the problem. magnitude of force A = 74 N direction of force A = 25o north of west second force = P direction of force P = α south of west arrow_forward The resultant of two forces is horizontal , it means that the y component of resultant = 0 Ry = ASin(25o) - PSin(α) 0 = (74×0.42) - PSin(α) PSin(α) = 31.08 NFor, the smallest force P , the value of Sinα must be maximum which is 1 when the value of αis 90 degree Thus, P×Sin(90o) = 31.08 N P = 31.08 N The magnitude of smallest force P = 31.08 N the direction of force P = 90 degree south of west = along - y axis= arrow pointing vertically downw
Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
A BB-series Astromech Droid of mass 181 kg is suspended by the truss structure shown. The truss structure is pinned to the wall at A and is supported by a rocker against the wall at F. B. 2w F Allow w = 1.5 m . Determine the forces in all the members in the structure and indicate whether they are in tension or compression. Part A - Part A Solve for the force in member AB and state whether it is in tension or compression. Express your answer to three significant figures in units of N. Enter negative value in the case of compression and positive value in the case of tension. Templates Symbols Slope/Displacement Vector undo redo reset keyboard shortcuts help FAB= N Submit Request Answer Part B - Part B Solve for the force in member BC and state whether it is in tension or compression. Express your answer to three significant figures in units of N. Enter negative value in the case of compression and positive value in the case of tension. femplates Symbols Slope/Displacement Vector uado…
What would be the resultant force F of the triangular distributed load and its location d measured from point A. 150 lb/ft A 3 ft 5 ft - 2 ft Select one: Ca.F=300 lb and d= 2.5 ft O&F-375b and d= 1.67 ft C F-750 b end d 3.67 ft d. F-375 b and d = 3.67 ft Finish atte ENG 12:44 US 4/18/2
If B=650 N Solve for: •Line of action of the Resultant Force •Horizontal and Vertical Force on each member •Gripping Force P •Magnitude of the Resultant Force -Include direction (upward, downward, N, E, W, S, or if Tensile or Compressive -Include 4 decimal points -Provide a readable solution