Refer to the steam power plant below and determine the following: ii. i. Specific enthalpy at the steam turbine inlet Specific enthalpy at the steam turbine exit Density at the pump entrance iii. Win P. 20 kPa T Tat@20kPa-5.6°C W Pump Boler Condenser Qout Steam Turbine P 8MPa T 450℃ Wout P. 20 kPa $*6.5579 kg K₂

Refer to the steam power plant below and determine the following: ii. i. Specific enthalpy at the steam turbine inlet Specific enthalpy at the steam turbine exit Density at the pump entrance iii. Win P. 20 kPa T Tat@20kPa-5.6°C W Pump Boler Condenser Qout Steam Turbine P 8MPa T 450℃ Wout P. 20 kPa $*6.5579 kg K₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reheater cycle is executed of 1 kg steam expanding initially from 12.547 Mpa and540.547 oC. The reheater pressures are 2.5547 Mpa and the steam leaves the reheaterat 420.547 oC. Condensation occurs at 0.02547 Mpa. Calculate W, ec and ee.
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 10. Calculate the net work of the cycle.
Find the turbine specific work, y=0.143 state 1 2 3 45 9 10 kJ/kg 226 236.1670 3602 2796 3481 2494 702 Turbine Boiler 6. 8. 4 Mixing chamber Closed Condenser fwh 2 10 3 PII PI
Q2Air enters an insulated turbine at 50°C, and exits the turbine at - 30°C, 100 kPa.The isentropic turbine efficiency is 70% and T1=50C V=20L/s the inlet volumetric flow rate is 20 L/s. What is the turbine Air turbine inlet pressure and the turbine power output? T2=-30C.P2=100kpa
Initial condition: P = 2 MPasaturatedProcess: AdiabaticFinal condition: P = 0.1 MPasaturatedRequired: Turbine isentropic efficiency
i need the answer quickly
b- An evacuated tank ,shown if fig of 1 ft3 is coupled to air supply line through valve .When the valve is opened, the air flow from supply line at 70°F,120 psi until the pressure reaches 90psi . calculate the final temperature and mass inside tank ,assuming the process is adiabatic. R= 53.34 Ibf-ft/lbm °R use the table below in case. Alr supply line Tank Idcat-Gas Propertiles of Air (English Units)0, Standard Entropy at 1 atm = 161.325 kPa = 14.696 1bf/in.² (R) (Btulbm) (Btu/lbm) (Btu/lbm R) (R) (Btu/lbm) (Btu/lbm) (Btu/Ibm R) 400 68.212 95.634 1.56788 1950 357.243 490.928 1.96404 440 75.047 105.212 1.59071 2000 367.642 504.755 1.97104 480 81.887 114.794 1.61155 2050 378.096 S18.636 1.97790 520 88.733 124.383 1.63074 2100 388.602 532.570 1.98461 536.67 91.589 128.381 1.63831 2150 399.158 546.554 1.99119 540 92.160 129.180 1.63979 2200 409.764 560.588 1.99765 560 95.589 133.980 1.61852 2300 431.114 588.793 2.01018 600 102.457 143.590 1.66510 2400 452.640 617.175 2.02226 1000 172.564…
I need help on the following question: The vapour compression cycle (picture provided), utilises the refrigerant R134a flowing at 0.05 kg s-1. Assuming that the compression is adiabatic and reversible. If the actual input power to the compressor is 2 kW, then: 1. You need to determine the theoretical input power to the compressor and the heat transfer (Φ) to theevaporator. Take the enthalpies h1, h2, and h3 to be 238.41, 263.68 and 81.5 kJ kg-1 (use the 'NH3 Refrigeration Table' where you can find online). 2. You need to determine the coefficient of performance based on your answer to the previous question (1). 3. You need to determine the compressors mechanical efficiency.
I need a clear and fast answer within 20 minutes. Thank you
A heat exchanger uses medium pressure steam at 10 bar and 350 C to heat cyclohexane vapor from 100 C up to 275 C as shown in the figure below. The steam is available at a flowrate of 32 kg/h and it condenses completely in the heat exchanger and exits as saturated liquid condensate at 10 bar. a) How much heat (in kW) can be provided by the steam? b) How much cyclohexane can be processed in kg/h? Vapor Cyclohexane T = 100 C P = 1 atm Steam T = 350 C = 10 bar Condensate P Vapor Cyclohexane T = 275 C P = 1 atm P = 10 bar
In an axial flow compressor air enters at 1 bar and 15 deg C. It is compressed through a pressure ratio of four. Find the actual work of compression and temperature at the outlet from the compressor. Take the isentropic efficiency of the compressor to be equal to 0.84. A. 147.66, 454.83 K C. 167.66, 454.83 K kg B. 157.66 444.83 K D. 177.66- 444.83 K