Saturated liquid Refrigerant-134a at 40°C is throttled to -10°C. The refrigerant then enters an evaporator and exits as saturated vapor. The evaporator is used to cool liquid water from 20°C to 10°C. If the mass flow rate of refrigerant is 0.01 kg/s, what is the mass flow rate of the water? R134a sat. liquid 40°C throttle -10°C water 20 °C evaporator water 10 °C sat. vapor

Saturated liquid Refrigerant-134a at 40°C is throttled to -10°C. The refrigerant then enters an evaporator and exits as saturated vapor. The evaporator is used to cool liquid water from 20°C to 10°C. If the mass flow rate of refrigerant is 0.01 kg/s, what is the mass flow rate of the water? R134a sat. liquid 40°C throttle -10°C water 20 °C evaporator water 10 °C sat. vapor

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thermodynamics Refrigerant R-134a to the compressor of a refrigeration machine It enters at 140 kPa pressure and -10 °C, and exits at 1 MPa pressure. Volumetric flow of the refrigerant entering the compressor It is 0.23 m³/minute. The refrigerant enters the throttling valve at a pressure of 0.95 MPa and at 30 °C, and exits the evaporator as saturated steam at -18 °C. Adiabatic efficiency of the compressor It is 78%. Show the cycle in the T-s diagram. And; a) Calculate the power required to run the compressor. b) Calculate the heat absorbed per unit time from the cooled medium. ( COPSM=? ) c) Calculate, between the evaporator and the compressor, how much the pressure of the refrigerant drops and how much the heat gain.
An ammonia refrigeration compressor takes its suction from the evaporator, at a temperature of-200F and a quality of 95%. The compressor discharges at a pressure of 100 psi, liquid ammonia leaves the condenser at 500F.(a)Determine the heat absorbed by the evaporator in kJ/kg. (b)Determine the heat rejected to the condenser in kJ/kg. (c)Determine the COP. (d)Determine the horsepower per ton of refrigeration. (e)Determine the quality of refrigerant upon entering to the evaporator
A three-stage compressor receives 500 lps of air at 101 kPaa and 27degrees Celcius, anddischarges at 750 kPaa. Determine a) the power required; b) the pressure at eachintercooler; c) the maximum temperature; and d) the heat transferred in each intercooler. e) What is the discharge temperature of a single-stage compressor operating at the sameintake and discharge temperatures?
300 kg/min of water is required to be cooled from 50°C to 25°C in a wet cooling tower. For these purposes, 730 m3/min of atmospheric air is circulated through it at countercurrent. If the atmosphere is at a pressure of 94 kPa and the dry bulb and humid are 25°C and 15°C, respectively, and in the mixing process 3.7% of water is lost per evaporation, determine*:a) Relative and absolute humidity and dew temperature of the atmosphere.b) Absolute humidity and temperature of the air at the outlet.
In a refrigerator the pressure in the evaporator us 2.72 kg/cm sq. and the refrigerant entry is 0.12 dry while at the exit 0.91 dry. During the compression, the work done per kg is 17,033 kg-m/kg. Calculate the COP. The rate of refrigerant circulation is 5.64 kg/min. The given latent heat and specific volume at 2.72 kg/cm sq are 320 kcal/kg ang 0.436 cu m/kg.
Consider that a flow of air with a velocity of 270 m/s enters an adiabatic diffuser at a pressure of 60 kPa and a temperature of 7°C and exits the diffuser at a pressure of 85 kPa and a temperature of 27°C. Use variable specific heat approach to indicate the air properties. Calculate the ratio of the inlet area to the exit area of the nozzle. A. 0.525 B. 1.254 O C. 0.886 O D. 0.356 E. 0.215
In an ammonia refrigerator , the pressure in the evaporator is 267. 58 KPa and theammonia at is 0.14 dry while at the exit is 0.86 dry . During compression the work done per kgof ammonia is 20 ,000 kg .m . Calculate volume of the vapor entering the compressor per minuteif the rate of ammonia circulation is 6.54 kg. The compressor has a volumetric efficiency of 90%and it runs at 150 rpm .The ratio of stroke to bore is 1 .Latent enthalpy of ammonia at basedon its evaporating pressure is 320 Kcal per kg and its latent specific volume of ammonia basedon its evaporating pressure is 0.436 m3 per kg .Specific volume of ammonia .A) 2.23 C) 2.46B) 3.23 D) 4.62
Properties of Carbon Dioxide: h@ 220 KPa and -5°C = 350 KJ/kg h@ 25°C = 223.65 KJ/kg h.@ 22°C = 220.75 KJ/kg h. @ 220 KPa = 347.13 KJ/kg %3D %3D %3D Saturated Vapor Carbon Dioxide refrigerant at 220 KPa leaves the evaporator and enters the compressor at -5 °C. The refrigerant leaves the condenser as saturate liquid at 25 °C and enters the expansion valve at 22 °C. Heat rejected from the condenser amount 90 KW. The work to the compressor is 60 KJ/kg while the heat lost from the compressor is 5 KJ/kg. If 2.5 KJ/kg of heat are lost in the piping between the compressor and condenser. Solve for the mass flowrate of the refrigerant in kg/hr.
Atmospheric air at 40°C dbt and 55% RH is passed over a cooling coil at the rate of 600 m'/mint. At exit from coil the air is saturated and its temperature is 8°C. The condensate also leaves at 8°C. Determine the amount of condensate leaving coil per minute and refrigeration in kW, The specific heat of superheated steam may be assumed to be 1.88 kJ/kg-K. Solve the problem without psychromatic chart.
I need help on the following question: The vapour compression cycle (picture provided), utilises the refrigerant R134a flowing at 0.05 kg s-1. Assuming that the compression is adiabatic and reversible. If the actual input power to the compressor is 2 kW, then: 1. You need to determine the theoretical input power to the compressor and the heat transfer (Φ) to theevaporator. Take the enthalpies h1, h2, and h3 to be 238.41, 263.68 and 81.5 kJ kg-1 (use the 'NH3 Refrigeration Table' where you can find online). 2. You need to determine the coefficient of performance based on your answer to the previous question (1). 3. You need to determine the compressors mechanical efficiency.
A reheat cycle with two stages of reheating is executed with steam expanding initially from 25 MPa and 600 °C. The two reheater pressures are 4 MPa and 1 MPa, and the steam leaves each reheater at 600 °C. Condensation occurs at 40°C. What is hi in kJ/kg?
Saturated steam at 40∘C is to be cooled to saturated liquid in a condenser. The mass flow rate of the steam is 17.3 kg/s . Assume no pressure loss. a)Determine the rate of heat transfer. Q = ? MW