Record the dimensions of the known (calibration) block using the caliper and dial gauge on the table below. Indicate theunits of each measurement. Calculate the average length of each side of the block.DimensionCaliper (Units)0.9951.4550.985Ruler(in) A: 0.9B: 1.5C: 0.9ABCDimensionABInstrumentUse the average dimensions (see Problem 2a) of the known block to calibrate the LVDT at your workstation. Record thevoltage on the table below:LVDT Offset: 0.556 (Do not include the offset value in your average dimensions)CAve Dimension (Units)(Dial Gauge)0.9971.6590.9490.964 in1.538 in0.945 inoltageAverage Dimension1.244 volt1.9941.280.964 in1.538 in0.945 in Use the LVDT to measure the length of each side of the unknown block provided by the TA. Record the voltage on thetable below. You will calculate the dimensions of the block as part of the post-lab assignment.DimensionA1.5951.533C1.858(Do not include the LVDT offset value in your final voltage numbers)VoltageBUsing the data collected during lab Part 2: Unknown Block Dimensions, complete the following:Develop a plot showing the relationship between the LVDT voltage and the dimension of the known block. Using Excel orsimilar software, determine the equation of the line that best fits the calibration data. Determine the dimensions of theunknown block using the LVDT data you collected.→ Hint: Plot dimension on the y-axis, and voltage on the x-axis.

Average Dimension (inches) Voltage (volts) 0.964 1.244 1.538 1.994 0.945 1.28

Record the dimensions of the known (calibration) block using the caliper and dial gauge on the table below. Indicate the units of each measurement. Calculate the average length of each side of the block. Dimension A B C 0.985 Ruler(in) A: 0.9 B: 1.5 C: 0.9 Caliper (Units) 0.995 1.455 A Dimension Average Dimension (Units) B Instrument C Use the average dimensions (see Problem 2a) of the known block to calibrate the LVDT at your workstation. Record the voltage on the table below: LVDT Offset: 0.556 (Do not include the offset value in your average dimensions) (Dial Gauge) 0.997 1.659 0.949 0.964 in 1.538 in 0.945 in Voltage Average Dimension 1.244 volt 1.994 1.28 0.964 in 1.538 in 0.945 in

Record the dimensions of the known (calibration) block using the caliper and dial gauge on the table below. Indicate the units of each measurement. Calculate the average length of each side of the block. Dimension A B C 0.985 Ruler(in) A: 0.9 B: 1.5 C: 0.9 Caliper (Units) 0.995 1.455 A Dimension Average Dimension (Units) B Instrument C Use the average dimensions (see Problem 2a) of the known block to calibrate the LVDT at your workstation. Record the voltage on the table below: LVDT Offset: 0.556 (Do not include the offset value in your average dimensions) (Dial Gauge) 0.997 1.659 0.949 0.964 in 1.538 in 0.945 in Voltage Average Dimension 1.244 volt 1.994 1.28 0.964 in 1.538 in 0.945 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In which of the following type of dimensioning, the dimensions are arranged only in a straight line? Staggered Dimension Parallel dimension Combined dimension O Aligned dimension
Show the tolerance zone created by each of the given tolerance specfication. Superimpose the tolerance zone on the given drawing.
The following figure shows a balance used to measure the mass of an orange cylinder. Read the value of that mass from the balance scale. 20 30 40 a. m = ( 22 ±1) gram O b. m = ( 24 ± 1 ) gram c. m ( 25 ± 2 ) gram O d. m = ( 24±2) gram
Find the taper angle, in radians, for a workpiece if a sine bar method was used. The stacked height is composed of the following gauge block values, 10, 15, 30, 4.5 and 1.3 mm. the length of the sine bar is 140mm. Support your answer with sketch.
SECTION B: OPTION 1 Convert figure below into ISOMETRIC & Do not dimension the drawing. All units are in mm. F.V 8 T.V R30 030 25 100 2 35 10 20 OF
The dependence of thermal conductivity of a material on temperature is given by an empirical equation k = a ebT where a and b are constants, and k is in W/m-K and T is in K. Spot the true statement from the following set. a, a and b have the same dimension as k. b. a has the dimension of k and b is dimensionless. c. a and b are dimensionless. d. a has the dimension of k and b has the dimension of T.
1.The thickness of a gage block is measured five times using an instrument that has a resolution of 0.001 cm. The following measurements are obtained (in cm): 1.100, 1.110, 1.090, 1.095, and 1.105. The true gauge block thickness is known to be 1.050 cm. Use this information to answer the following questions: a. What errors or sources of measurement error can be identified in the example? (Hint: there are three). Identify each one as a random or systematic uncertainty. b. Estimate the magnitudes of each of these uncertainties. Wherever possible, estimate random uncertainties at a 95% probability/confidence level. c. Based on the uncertainties determined in part b, estimate the overall uncertainty of a measurement obtained by this instrument.
6. On an engineering drawing a dimension is laid out as 1.760 + 0.005 A note on the drawing states that all dimensions are in inches. Give numerical values for (a) The nominal dimension (b) The upper limit (c) The tolerance (d) The bilateral tolerance
Q1/ The physical change in dimensions of the material and its state as a result of an increase in temperature under constant : pressure is called
Using only Table A (Conversion of Units), calculate the values asked. All answers must be given with the primary dimensions and units of the SI system. 988 465 mg a substance fills a volume of 3 288in3 , determine the specific volume
0 5 10 0 Answer: 35 30 25 20 15 5 10 35 30 25 20 15 Suppose that you measure the length of an object by using a mictometer caliper and read the measured length as shown in the figure. Write down the value you read from the figure in units of mm. Pay attention to use the correct number of significant figures.
2. Make ten measurement for the diameter of the spherical ball first with vernier caliper, then micrometer. Then, fill the table with your results. Vernier Micrometer No. Caliper (mm) 6.05 6.05 (mm) 5.96 6.04 2 3 6.00 6.02 4 5.90 5.98 6.10 5.94 6 5.85 6.08 5.95 5.95 6.00 5.99 6.00 5.98 10 6.05 6.00 Determine average absolute deviation, sample standard deviation, sample variance and coefficient of variation for diameter measurement at Instruction 2 for both vernier caliper and micrometer.