2. Make ten measurement for the diameter of the spherical ball first with vernier caliper, then micrometer.Then, fill the table with your results.VernierMicrometerNo.Caliper (mm)6.056.05(mm)5.966.04236.006.0245.905.986.105.9465.856.085.955.956.005.996.005.98106.056.00Determine average absolute deviation, sample standard deviation, sample variance and coefficientof variation for diameter measurement at Instruction 2 for both vernier caliper and micrometer.

Mean calculated is 5.9+6.12=6Now calculate deviation from mean S.no Deviation from…

2. Make ten measurement for the diameter of the spherical ball first with vernier caliper, then micrometer. Then, f the table with your results. Micrometer (mm) 5.96 6.04 Vernier No. Caliper (mm) 6.05 6.05 6.00 5.90 6.10 5.85 3 6.02 4 5.98 5 5.94 6.08 5.95 5.99 6.00 5.98 5.95 6.00 6.05 10 6.00 . Determine average absolute deviation, sample standard deviation, sample variance and coefficient of variation for diameter measurement at Instruction 2 for both vernier caliper and micrometer.

2. Make ten measurement for the diameter of the spherical ball first with vernier caliper, then micrometer. Then, f the table with your results. Micrometer (mm) 5.96 6.04 Vernier No. Caliper (mm) 6.05 6.05 6.00 5.90 6.10 5.85 3 6.02 4 5.98 5 5.94 6.08 5.95 5.99 6.00 5.98 5.95 6.00 6.05 10 6.00 . Determine average absolute deviation, sample standard deviation, sample variance and coefficient of variation for diameter measurement at Instruction 2 for both vernier caliper and micrometer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6. Comment on accuracy and precision of the spherical ball diameter measurements at Instruction 2
6. Comment on accuracy and precision of the spherical ball diameter measurements at Instruction 2 2. Measure the diameter of spherical ball five times with micrometer Then, fil the table with your results. No. Micrometer (mm) 1st 8.01 2nd 8.00 3rd 8.00 7 99 7 08 4th 5th
Incorrect answer I've tried below (should be in inches) .0152 7.64*10^-3 .00556 29007 .0101 .0122
cm ở 1 2 3 4 5 6 7 8 9 10 Main Scale Vernier Scale 1. The diameter of a certain circular shaft manufactured in Andaya's Engineering works is measured by a vernier caliper. The reading is shown below. Determine the range of the diameter of the shaft (Note: there are three (3) possible measurement of the said diameter
6. On an engineering drawing a dimension is laid out as 1.760 + 0.005 A note on the drawing states that all dimensions are in inches. Give numerical values for (a) The nominal dimension (b) The upper limit (c) The tolerance (d) The bilateral tolerance
Suppose that the length of the steel bar is measured by a number of different observers and following set of 11 measurements is recorded as set A (units mm): 398, 420, 394, 416, 404, 408, 400, 420, 396, 413, 330. Next the measurements are taken using different ruler to produce measurement set B: 409, 406, 402, 407, 405, 404, 407, 404, 407, 407, 408. It can be shown that the mean values set A and B are 409 and 406 respectively. Which of the two measurement sets A and B, and the corresponding mean value, should have most confidence in? why? Text
0.5mlm 1 3 4 5 cm mm} Consider the steel ruler shown. Which of the following dimensions can be accurately measured with this ruler? C. 1.05 mm B. 1.5 mm A. 1.25 mm D. All of these dimensions can be measured accurately
1) Calculate the extension e of the hinge line of brachiopod shell using the following formula. Here, the original length of the undeformed brachiopod shell in cm is l,, the deformed length of brachiopod shell in cm is /, , Measure the length of 1, and 1, of hinge line of undeformed and deformed brachiopod using the metric ruler. Substitute 5.5 cm for 1, and 6 cm for l. e = 6-5.5 5.5 e = 0.091 2) Calculate the angular shear y using the following formula. w = 90° – 0 Here e is the angle subtended by the deformed perpendicular line with the hinge line. Measure the angle 0 using the protractor in the deformed brachiopod. Substitute 45° for e. リ= 90°-0 = 90° - 45° = 45° Calculate the shear strain y using the following formula. y = tan ự Here y is the angular shear of the shell. Substitute 45° for y. y = tan y = tan 45° y = 1
Given the following mechanical engineer's scale, deter- mine the readings at A, B, C, and D. C- 10 12 A ENLARGED VIEW 50 4 6 8 10 12 14 16 FULL SIZE; 1:1; 1"=1" © Cengage Learning 2013.
Metric Vernier Caliper 1. Read the metric vernier caliper measurements for the following settings. d. MAIN SCALE MAIN SCALE 30 40 80 90 5. 10 15 20. 25 5. 10 15 20 25 VERNIER SCALE 0.02 ma VERNIER SCALE 0.02 mm MAIN SCALE MAIN SCALE 60 70 50 60 5. 10 15 20 25 5. 10 15 20 25 VERNIER SCALE 0.02 mm VERNIER SCALE 0.02 mm MAIN SCALE MAIN SCALE 10 20 20 30 10 15 20 25 5. 10 15 20 25 VERNIER SCALE 0.02 mm VERNIER SCALE 0.02 mm
1. Determine the reading on the vernier scale as indicated by the arrows. OMARKS 5 3 4 5 6 7 8 9 10 Reading.. .mm Page 6 of 7 LO
using the sine bar technique, find the value of the angle for the given data: the stacked height was composed of the following values, 30, 20, 5, 2 and 1.1 mm. The length of the sine bar is 150 mm. Support your answer by sketch.