The following figure shows a balance used to measure the mass of an orange cylinder. Read the value of that mass from the balance scale. 20 | 30 40 a. m = ( 22 ± 1) gram b. m = ( 24 ± 1 ) gram c.m = ( 25 ± 2 ) gram

The following figure shows a balance used to measure the mass of an orange cylinder. Read the value of that mass from the balance scale. 20 | 30 40 a. m = ( 22 ± 1) gram b. m = ( 24 ± 1 ) gram c.m = ( 25 ± 2 ) gram

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I only need the answer to part c and part d Newton's second law of motion was used to obtain the differential equation mi = -kx - câ that models harmonic motion. a) The dots denote differentiation with respect to time t. Explain the meaning of each term (there are three) and each factor (there are six) in the equation. If MKS (meters, kilograms, seconds) units are used, what are the units of each of the six factors? b) Suppose m =and k = 4 (MKS units). What values of c correspond to a system that is i) i) ii) underdamped, overdamped, and critically damped? c) Solve the critically damped case of the IVP = -4x - ck, x(0) = 1,¿(0) = -10. d) Find the value of t at which x(t) = 0
1.2 Please help. Written on paper not typed on computer or keyboard please. Need help both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Dynamics of Rigid Bodies Please help ASAP. Rate will be given accordingly. Please answer correctly. Please write your answer on paper. Thank you so much. Note: The tolerance is ±1 in the third significant digit.
The floor area of the model in the image below is 500 square inches, and the floor area of the house is 1,280 square feet. If the model has a room with a side length of 5 inches, then what is the scale factor for the model to the actual floor? ©2018 AlessandoMassiniano / Getty mages Plus O 5 in:8 ft O 5 in:12 ft O 5 in:36 ft O 5 in:64 ft
Please be consistent with the units. Don't convert SI to English or vice versa.
(b) A ship is moving relative to the water and you are given the following velocities: Magnitude Direction (degrees) (kn/hour) Velocity Absolute water velocity (tide) Ship's velocity relative to water 8 120 20 90 The directions are measured clockwise from due north (i.e. due east is 90°). What is the ship's absolute velocity (magnitude and direction)?
The Celsius degree is a smaller temperature unit than the Fahrenheit degree and both scales are not considered as an absolute one Select one: True O False
Q1. The image below shows an example of "absolute dependent motion analysis", where the motions of two objects depend on each other, and the goal is to find the relations in their motions (i.e., in their positions, velocities, and accelerations). Please put the suggested steps of analysis in the correct order. VA A B VB Differentiate the entire equation with respect to time, and extract the relation in velocities. Repeat for acceleration if needed. Set up a coordinate (s) along the direction of motion from a fixed point (O) or a fixed datum line. Represent the positions of the objects respectively. In some cases intermediate objects need to be considered too and their positions need to be represented as well. Recognize the constant length(s) and find the depending geometric relations between the position variables.
Write two or three Sentences about each of the following: Standard GaugeLimit GaugeIndicating GaugeCombination GaugeWorkshop GaugeInspection GaugeMaster Gauge (Reference Gauge)Dimension Measuring GaugeInside Dimension Measuring GaugePlug GaugePin Gauge Outside Dimension Measuring GaugeSnap GaugeRing GaugeBoth sides Dimension Measuring GaugeCalliper GaugeGeometric Measuring GaugeGauges for concentricityGauge of TaperGauge of ProfileSingle limit and Double limitSingle-ended and Double-endedFixed and Fastened
3. The force of a linear spring is given by F = kx, where F and k are the force on the spring and its stiffness, respectively. What is the dimension of k in the MLT system of units? a. M/L ML/T² b. F/L M/T² 4. A vehicle is running at 80 kph in a highway. If its wheel has a diameter of 524 mm, how fast is it turning in rpm. Assume that there is no slippage between the ground and the wheel. C. 742 d. 810 a. b. C. d. 565 675
Needs Complete solution with 100 % accuracy. Don't use chat gpt or ai i definitely upvote you be careful Downvote for ai or chat gpt answer.
Please answer number 2 to number 6