0.170 m20.300 mLraise the load L. If the system is initially at rest and a con-stant torque motor attached to the smaller gear A gives ita constant angular acceleration of a = 2.5 rad/s², deter-minea. The amount of time required to raise the load L a dis-tance of 5 m.b. The number of revolutions Ng that the larger gear turnswhile lifting the load L a distance of 5 m.C. The velocity of load L when it has risen 5 m.

Answered: Image /qna-images/answer/d4796691-ac23-4bc3-b07a-3fc3c87a1eb1.jpg

raise the load L. If the system is initially at rest and a con- stant torque motor attached to the smaller gear A gives it a constant angular acceleration of aA = 2.5 rad/s², deter- mire The amount of time required to raise the load L a dis- tance of 5 m. b. The number of revolutions Ng that the larger gear turns while lifting the load L a distance of 5 m. C. The velocity of load L when it has risen 5 m.

raise the load L. If the system is initially at rest and a con- stant torque motor attached to the smaller gear A gives it a constant angular acceleration of aA = 2.5 rad/s², deter- mire The amount of time required to raise the load L a dis- tance of 5 m. b. The number of revolutions Ng that the larger gear turns while lifting the load L a distance of 5 m. C. The velocity of load L when it has risen 5 m.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.60P: The force P applied to the brake handle enables the band brake to reduce the angular speed of a...

See similar textbooks

Similar questions

Important problem. The motor produces a counterclockwise torque 1 N.m on the attached disk A. A Part of this torque is transferred to the disk C through the belt after amplification. The disk A has mass 0.5 kg. and the disk C has mass = 4.5 kg. Find: (50 m 5omm pully C I. The difference tension between the palley A Te belt parts (7- T). II. The angular acceleration of the disk С. The angular acceleration of disk A. The angular velocity of the disk C after 5 seconds from the motion start. The transferred torque to the disk C. III. IV. V.
The linkage consists of two 4-kg rods AB and CD and a 18-kg bar BD. Rod CD is subjected to a couple moment M = 16 Nxm. When 0 = 0°, rod AB is rotating with an angular velocity w = 3 rad/s. I=1.9m B e 0 roo 2 D M Find the angular velocity w when = 52deg. Give your answer with 2 decimals.
Use 3 decimal places The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. 1. Find the velocity of the block after it moves 20m starting from rest. 2. If the 100-N pull is then removed, find the distance the block will travel.
(a) Find the final speed V of the center of mass of the wheel once the wheel starts moving.
The slender 8-kg bar AB is horizontal and at rest. The spring has an unstretched length sọ of 1 m and a spring constant of 15 N/m. the length of the bar AB is l1.Sm Find the angular velocity when e - 45° when the bar has rotate clockwise - 45° after being released. Give your answer with 2 decimals and include the sign
Use 3 decimal places The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. 1. If the 100-N pull is then removed, find the distance the block will travel. 2. Find the velocity of the block after it moves 20m starting from rest.
A spring with a spring constant of 1200lbf/ft is attached to block with a mass of 96.6lbm horizontally. It was initially displaced 3 inches to the left of the equilibrium position and released at 12in/s going to the right. Determine also the c) acceleration 2 seconds after the push in ft/s2 *
Q2 -1- For the mechanism shown determine for all moving points. A -The number of degrees of freedom. B-Velocity diagram. C- Acceleration diagram. D-The number of instantaneous center. (45°) AB=40mm, BC=120mm, w=12rad/s., ø= 1orod/s AB = 2 50mmn
A cyclist pedals constantly at 7.9587 rad/s the wheels are 336.5mm in radius. If the chain is directly connected with the sprockets which are 76 mm in radius (front sprocket) and 35mm in radius (rear sprockets), Determine the angular speed of the wheel in rad/s.
Q1/ A shaft rotating at 120 r.p.m is supported in bearing A and B, 1.8 m apart, A being at the left- hand end. Two unbalanced rotating masses of 7.5 kg and 10 kg at radii of 75 mm and 50 mm respectively are situated between A and B at distances of 0.6 m and 0.9 m respectively from A. The angle between the radii is 60" when viewed along the shaft. Answer the following questions: 1- The dynamic forces are. 2- Forces on bearings A and B due to dead weight are .. ., and. 3- Resultant force at A and B are .. . and 4- A rotor supported at A and B carries two masses. The rotor is (a) dynamically balanced (b) statically balanced (c) both (a)&(b) (d) none. and ..
2) The 50-kg wheel is connected to a 10-kg block as shown. The block is moving downward with a speed of 2.4 m/S, and suddenly, friction between the wheel and ground was applied, and caused the block to decelerate at 10.0 m/ S. A) Draw the FBD and KD for the wheel alone, and show all external and effective forces on these diagrams. B) Calculate the angular acceleration of the wheel. C) Assuming the wheel has angular acceleration of 25 rad/ S? find the acceleration vector of the center of mass of the wheel.
The slider P can be moved inward by means of the string S as the bar OA rotates about the pivot 0. The angular position of the bar is given by 0 = 0.4 +0.12t+ 0.06t³, where 0 is in radians and t is in seconds. The position of the slider is given by r = 0.8 0.1t 0.05t2, where r is in meters and t is in seconds. Determine and sketch the velocity and acceleration of the slider at time t = 2 s. Find the angles a and ß which v and a make with the posi- tive x-axis. S 0 Problem 2/144 رفع جك