Question No. 1 The switch S₁ of figure 5 has been closed for a long time. At t=0sec, S₁ is opened, at the same instance S2 is clo a) Find the initial current through the coil b) Find the mathematical expression for the current (iz) through the inductor and corresponding voltage (vz) following the closing of the switch S2 c) Sketch the wave form for it and VL 81 82 8.2K2 -。xt-o www. 12mA www 1K2 F2.2K L 680mH Ju H Figure 5: RL circuit network for question no.5

Question No. 1 The switch S₁ of figure 5 has been closed for a long time. At t=0sec, S₁ is opened, at the same instance S2 is clo a) Find the initial current through the coil b) Find the mathematical expression for the current (iz) through the inductor and corresponding voltage (vz) following the closing of the switch S2 c) Sketch the wave form for it and VL 81 82 8.2K2 -。xt-o www. 12mA www 1K2 F2.2K L 680mH Ju H Figure 5: RL circuit network for question no.5

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
please solve value of Capacitor with 0.1V Ripple. And draw output ripple waveform. Explain it one by one for me thanks..
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
Find the Igms value of the square waveform of Figure Q1) cof Figure Waveform
For the circuit below assuming an ideal switch, preform transient analysis to predict the voltage across resistor, R2 and plot the results. The inductor will have zero current as initial condition. L1 0.005 2 U1 100mH R1 1k V1 20Vdc R2 100
A capacitor in series with a 200 ohms resistor draws a current of 0.3 ampere from 120 volts, 60 hz source. What is the value of the capacitor in microfarad? a. 8.7 b. 9.7 c. 6.7 d. 7.7
1. Which of the following answers best describes discontinuous conduction mode? A. The inductor voltage ripple goes negative B. The inductor current ripple stays positive C. The inductor current ripple falls to zero D. The output current ripple falls to zero
4) Determine the value of branch current, I1 and I25) Determine the value of voltage across resistor, R1, R2 and R36) Determine the value of voltage across capacitor, C1 and C27) Determine the value of voltage across inductor, L.
Show the Analog Waveform Signal of the problem below. Please include the formula you will be using to get the waveform, also include what application you will be using to get the waveform. If you will use sine or cosine, please include the whole formula so I could just substitute it from the problem below. Problem: An oscilloscope's output is an analog signal that ranges only from 12.5mV to 50mV, while its highest frequency is 50kHz.
Question A sinusoidal signal with a peak voltage of 10V is input into a frequency dependent circuit. What is the peak voltage at its -6dB frequency?
Half-wave 50Hz sinusoidal uncontrolled rectifier circuit with a peak voltage value of 100V and a source inductance of 8mH is feeding a highly inductive load of 8A. The average value of the output voltage and power delivered are, respectively and what is the communication angle (u) Power Electronics