QUESTION 5 Given the truss and loading shown below, determine the stress at member CD if Pu = 18.375 Kips and its area is 23 in2. Assume that the truss are simply supported at joint M and E. Express your answer in ksi. Use three decimal places. 14.257 8²1 RM Pu Pu Pu Pu Pu 8@10' = 80' B Pu O Pu et LK J I H G F 8@10' 80' Re

Q: In what directions do sound waves move?

A: Sound wave propagates as an acoustic wave which have oscillation in pressure, stress, particle…

Q: A HAY BROUGHT- IN HERE HAY HOLES ANIMAL FEEDING AREA HAY STORAGE QUESTIONS: 1. What is the SPECIFIC…

A: To mention the specific name of the structure shown in the figure.

Q: What is meant by ephemerides?

A: Ephemerides is a term related with astronomy and celestial navigation.   Ephemerides is a table…

Q: What is wrong with the picture at right?" (<25 words) YES! Safel NOI Unsafel

A: A picture including of two images where different cases of cylinders were given.

Q: Please answer problem 4 and problem 5 please

A: Solution: Problem 4: Let L = a x b ∑Mc=0 RAa+b-Pb=0RA=Pba+b=PbL

Q: Dr. X, a distinguished structural engineer, received a phone call from an engineering student at a…

A: Structure engineer is the mainly connected with the building by its resistance against different…

Q: What is kinematics? What is meant by pitch, yaw and roll?

A:

Q: B A railroad crossing with a passive control is formed by a two-lane highway with a design speed of…

A:

Q: Determine number of external indeterminacy

A: Given data : Number of external support reaction (R)=3+3=6 m=Number of member connected at hinge…

Q: How can I find GH, EG and FH

A:

Q: Q1. Draw N,V &M diagrams 10 kN/m A to B 3m KN 40 2″m 3m 4m

A:

Q: Distinguish between intermittent system and continuous system of water supply

A: In Intermittent system water supply is divided into several zone and each zone is supplied with…

Q: can u get the

A:

Q: Elements & Principles of Design (Pre-assessment) 1. What is the definition of the elements of art?…

A: 1) Definition of elements of art:     Option B: The building-blocks of any artwork. 2) Elements of…

Q: What design changes to either the task or equipment could you make that would either compensate for…

A: When it comes to compensating for limitations in human senses or capitalizing on other human…

Q: Is this a three moment equation problem

A: The procedure followed is not three moment equation method.

Q: (b) Design the Beam B-B for the maximum sagging section only. Your design should consider the…

A: L=4.55 mh=22.2 mt=122 mmDL=3.55 kPaLL= 4.55 kPafck= 25.5 Mpafy=472 MpaTo design- 1) Loads2) Design…

Q: Differentiate force system based on line of action.

A: A force is a push or pull on an object caused by its interaction with another object.

Q: what is mercury manometer? own words

A:

Q: Differentiate between Directed Changes and Constructive Changes.

A: Directed Changes are the changes that are specifically directed by the owner which may or may not…

Q: Determine degree of total indeterminacy

A: Given data : The given structure is truss structure . It is pin connected carrying tension or…

Q: wrong given, pls. answer

A: Given: Span= 10m, axle loads as shown in figure

Q: What are the possible sources of error in measurement?

A:

Q: What is the use of a magnetic needle?

A: Magnetic needle The magnetic needle is used in compasses that are magnetic in nature.

Q: A drone is flying in the air at some altitude. The drone is equipped with piezometer that indicates…

A:

Q: What do you mean by Eddy in the atmosphere?

A: Answer:- Eddy: Small eddies takes place in day time in earths atmosphere, when surface air is heat…

Q: 200 mm 200 mm 400 mm

A: Section  Area  x Remarks  ABC A1  = π42002      = 31400 mm2 x1 = D2    = 2002     =100 mm   AEF…

Q: Please double check the answer if this is correct!

A: Given, σall = 300 kPa a = 20 mm b = c = 250 mm

Q: Q1: a-How to draw a perpendicular from point outside of straight line. • b-Complete in all respects…

A: (a) How to draw a perpendicular from straight line: Cross staff is used for setting out the…

Q: What are Frontal Inversions?

A: Inversion is used when metrological inversion of temperature takes place. It is an alteration from…

Q: Define Earthquakes.

A: Earthquake is any sudden ground shaking triggered by the seismic waves passing through rocks of the…

Q: What are servomotors?

A: Servomotors are used in cars to control its speed.

Q: Is there any other way to got forces?

A:

Q: noose best option. how would you ct set of objects in a drawing? * None of the above By a crossing…

A: By a crossing window is drawn from right to left the set of objects can be selected. Option (b) will…

Q: What is the measure of position? What is the measure of variation? How do you find the measure of…

A: 1. What is the measure of position? A measure of position is very helpful in determining the…

Q: Explain the difference between average and instantaneous speed.

A: The overall distance traveled by the object in a given time frame is the average speed. A scalar…

Q: How does backwashing a filter in water treatment cause head loss. Please explain

A: Backwashing a filter in water treatment causes head loss due to the rearrangement of filter media.…

Q: This is a photograph of Claude and Holly Duval from Montreal in Canada. They are on holiday in New…

A: Step 1

Q: 3. The tractor is used to lift the 250-kg load B with the 28m-long rope, boom, and pulley system. If…

A: Determine tension in the rope,T=?

Q: *Draw the Frontal section 50 25 25 10- 40 RIS 20 60 80 20

A: Finding out front view of the isometric section.

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.