Question 4- Transmission Lines a) Describe the relationship between Line-to-Neutral and Line-to-Line in a 3-phase system. b) Explain how the ABCD matrix is derived from voltage and current relating to a transmission line. Your explanation should also interpret what A, B, C and D are in relation to their units from the point of view them being coefficients.

Question 4- Transmission Lines a) Describe the relationship between Line-to-Neutral and Line-to-Line in a 3-phase system. b) Explain how the ABCD matrix is derived from voltage and current relating to a transmission line. Your explanation should also interpret what A, B, C and D are in relation to their units from the point of view them being coefficients.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.37P

See similar textbooks

Similar questions

Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
In a string of suspension insulator with three units, the line unit has 20kV and k=0.35. The voltage across tower unit is........ and across middle unit is.......
please solve for nodal stress method. (if it is possible to apply supernodes)
Q2) In the network in the figure below Y-Y connected transformers, each with grounded neutrals, are at the ends of each transmission line that is not terminating at bus 3. The transformers connecting the lines to bus 3 are Y-A, with the neutral of the Y solidly grounded and the A sides connected to bus 3. All the line reactances shown in the figure between busses include the reactances of the transformers. Zero sequence values for these lines including transformers are 2.0 times those shown in the figure. Both generators are Y-Connected. Zero-sequence reactances of the generators connected to bus 1 and bus 3 are 0.04 and 0.08 per unit, respectively. The neutral of the generator at bus 1 is connected to ground through a reactor of 0.02 per unit; the generator at bus 3 has a solidly ground neutral. Find the bus impedance matrices (¹), (²), z for the given network and 'bus' 'bus' bus then compute the Subtransient current in per unit for a single line-to-ground fault on bus 2 and the fault…
Calculate the initial symmetrical short circuit current that will occur when a 3 phase short circuit error occurs at the F point in the Figure below İ k3 phase-max ?
In a string of suspension insulator with three units,the line unit has 12k and k=0.15. The voltage across tower unit is and across middle unit is .?: a. 8.14kV & 9.37 kV b. 8.27kV & 10.34kV c. 9.20kV & 12.42kV d. 10.18kV & 11.71kV
() State TWO (2) advantages of three-phase system over single-phase system. (ii) For a three-phase system with delta load connection, derive line and phase current relationship as stated in equation (2.1). line = V3lpnase 4 – 30 A (2.1)
Consider three ideal single-phase transformers (with a voltage gain of ) put together as three-phase bank as shown in Figure 3.35. Assuming positive-sequence voltages for Va,Vb, and Vc find Va,Vb, and VC. in terms of Va,Vb, and Vc, respectively. (a) Would such relationships hold for the line voltages as well? (b) Looking into the current relationships, express IaIb and Ic in terms of IaIb and Ic respectively. (C) Let S and S be the per-phase complex power output and input. respectively. Find S in terms of S.
Consider the single-Line diagram of a power system shown in Figure 3.42 with equipment ratings given: Generator G1: 50MVA,13.2kV,x=0.15p.u. Generator G2: 20MVA,13.8kV,x=0.15p.u. Three-phase -Y transformer T1: 80MVA,13.2/165YkV,X=0.1p.u. Three-phase Y- transformer T2: 40MVA,165Y/13.8kV,X=0.1p.u. Load: 40MVA,0.8PFlagging,operatingat150kV Choose a base of 100 MVA for the system and 132-kV base in the transmission-line circuit. Let the load be modeled as a parallel combination of resistance and inductance. Neglect transformer phase shifts. Draw a per-phase equivalent circuit of the system showing all impedances in per unit.
For an NN square matrix A, in (N1) steps, the technique of Gauss elimination can transform into an ____________ matrix.
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.