QUESTION 3: Refer to the following figure. The circuit parameters are: V*= 4.5 V, V = -4.5 V and R1 = 9.3 k2 Assume that the transistor parameters are: B = 60 , VBe(on) = 0.7 V, and V4 = 112 V. Determine the percent change in Io as VCE2 changes from 0.7 V to 5 V caused by change in V7 in the load circuit. IREF (mA) Format : 0.5644 Io (mA) Format : 0.5373 Ro (kN) Format : 322.7332 Percent change in Io (%) Format : 9.9276 V+ Load I circuit RC IREF R Vo VBEO lo + VCEI Q1 Q2 VCE2 + V BE

QUESTION 3: Refer to the following figure. The circuit parameters are: V*= 4.5 V, V = -4.5 V and R1 = 9.3 k2 Assume that the transistor parameters are: B = 60 , VBe(on) = 0.7 V, and V4 = 112 V. Determine the percent change in Io as VCE2 changes from 0.7 V to 5 V caused by change in V7 in the load circuit. IREF (mA) Format : 0.5644 Io (mA) Format : 0.5373 Ro (kN) Format : 322.7332 Percent change in Io (%) Format : 9.9276 V+ Load I circuit RC IREF R Vo VBEO lo + VCEI Q1 Q2 VCE2 + V BE

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Vin For the circuit shown, assume that Vo = 3V and that the transistor is described as follows: B-100, Va = 100V, VT = .025V. a) Determine the small signal parameters for the transistor. b) Draw the small signal model 5V 5V 300uA Vo www 4K 625 C
1) Determine the maximum value of the resistor that will cause the transistor to work in the saturation region, consider the B=100. %3D 8V 4700 RB LED verde (1.5V) LED rojo (1.8V) -Write the result in kilo-ohms----
Question-3 a. Determine the Q point of the transistor circuit shown in Figure below. b. Also draw the d.c. load line. + Vcc Ic + 10V 1k2 RB B = 100 47 k2 VBE RE 4.7 k2 - VEE 6- 10V
3. Design a four-resistor BJT bias circuit, similar to the one shown in Figure 2, such that V3 = 4 V and Ic = 1 mA. Assume VBE (on) = 0.7 V and B-150 for the transistor. 12V R1 R2 10k RC 5.6k Q2N2222 RE Figure 2 Note: Use PN2222A in Multisim
For the BJT circuit shown in Figure b, find the operation point of the transistor. (use B=100 for BJT) Rc 9 k2 Vcc= 2.5 V Rp1 k2 Maximum file size: 51 Files
Identify the source, drain, gate, and bulk terminalsand find the current I in the transistorsAssume VTN = 0.70 V
2002, 100kN, Rc = 1kN, RĘ The parameters of the npn transistor circuit in Figure 1 are R1 VBE = 0.7V,and Vcc = 12V. Calculate IB, Ic, Ip, and VCE at the operating point if Bp = 50. +Vcc Ic R1 RC C IB Q1 B E RE OV
EHide bla This course Determine Vx and the mode of operation of the PNP transistor shown in the figure below. Assume Is = 2.5x106 A,B- 50, VA =, and Rc = 0.1 KO. Vec 2 V EX 1.2 V- Re幸 Select one: O a.1.153 V. Active Mode O60577V. Active Mode Oc 023 V. Active Mode d. None of these Oe 2306 V Saturation Mode For the circuit shewn in the figure below. assume l = 3 107A V= 26mv. B= 100, and V = The value of r-5
Vec +12V Re 1kS2 Re 470k2 BC107 Vc Ve Figure 3: Practical Fixed Bias Transistor Circuit 2. Measure the DC voltages Vc and VB using digital multi-meters. Determine the quiescent base current, collector current, and collector- emitter voltage.
A common- configuration has the input at the base and the output iat the collector. base emitter collector
4. The voltage divider-bias method is so named because: A. The circuit design resembles a knife B. The approach is cutting edge C. You have to split one of the resistors D. A voltage divider is used to supply the bias current for the transistor
For the circuit in Figure below, what is Ic3? Assume all transistors are identical. IREF 1 Q5 R1 IREF2 O IE of Q2 O 2 IREF1 O IE of Q1 Vh1 Q6 Q1 03 07 8 Vn2 04 IREF2 R2