Question 2. Questions regarding the 4-bit right shit register built in the experimental part. a. How many bits can this register store at a time? Explain your answer. b. Consider this Dataln sequence: 1001100000 for a SISO right shift register. The initial state of each D flip-flop is 0. How much is out1, out2, out3, out4 after the third clock cycle happens? Explain your answer by including all the steps.

Question 2. Questions regarding the 4-bit right shit register built in the experimental part. a. How many bits can this register store at a time? Explain your answer. b. Consider this Dataln sequence: 1001100000 for a SISO right shift register. The initial state of each D flip-flop is 0. How much is out1, out2, out3, out4 after the third clock cycle happens? Explain your answer by including all the steps.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) IC's for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop 7-Segment Display Button Decoder Circuits Circuits
23. The following serial adder uses two four-bit registers. Register A holds the binary number 0101 and register B holds 0111. The carry flip-flop is initially reset to 0. List the binary values in register A and the carry flip-flop after each shift. SO Shift register A Shift SI control CLK Serial input SI sO Shift register B Clear
1. An 8-bit register contains the number 10000110. The serial number 11011011is applied to the input. After 5 shift pulses, what is the number in the shift register? Assume shift right operation 2. A binary number is shifted 5 positions to the left. The number therefore has been 3. A binary number must be divided by 128. How many positions must the number be shifted (and in what direction to achieve this?
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
Design a four‐bit shift register with parallel load using D flip‐flops. There are two control inputs: shift and load. When shift = 1, the content of the register is shifted by one position. New data are transferred into the register when load = 1 and shift = 0. If both control inputs are equal to 0, the content of the register does not change.
The figure below shows a four-bit binary ripple counter that is initially in the 0000 state beforethe clock input is applied to the counter. Clock pulses are applied to the counter starting at sometime t1 and then removed some time later at another time t2. The counter is observed to read 0011.How many negative-going clock transitions have occurred during the time the clock was active atthe counter input? Give the three lowest possible answers. Please show your process.
1) Draw timing diagram. Q0,Q1,Q2,Q3 start with 0 HIGH —o CLK 2) Design a four-bit shift register with parallel load using D flip-flops. There are two control inputs: shift and load . When shift = 1, the content of the register is shifted by one position. New data are transferred into the register when load = 1 and shift = 0. I both control inputs are equal to 0, the content of the register does not change.
Supnorting.cxcentions &interruats Select True/False (T/F) for each statement. Exception usually refers to an event outside of the CPU and interrupt refers to an event inside the CPU. ISelect The CPU checks for exceptions/interrupts after every assembly instruction to get to them tast. Select With polled interrupts, the hardware is responsible to identify the source of the event. Select) With vectored interrupts, the hardware is responsible to identify the source of the event. I Setect)
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
21. Draw the logic diagram of a 4-bit register with four D flip-flops and four 4x1 multiplexers with mode selection inputs si and so. The register operates according to the following function table So Register Operation No change 1 Complement the four outputs 1 Clear register to 0 (synchronous with the clock) 1 Load parallel data
1) What is the biggest binary number (decimal value) you can write with 6 bits? What is the biggest binary number (decimal value and in terms of n) you can write with n bits? If you want to represent the decimal numbers from 0-16, what is the minimum number of bits you will need? Convert the decimal number 238 to binary number. (ZERO point if not showing steps/calculation!)