Question 2. Considering this figure. The firingangle is 45°, the motor current is 10 A, and the supplyvoltage is 110 v.0₁ 0₂90(a) Draw the waveforms of v, Vo. io. isi, iDi, and i.(b) Determine the power taken by the dc motor.(c) Determine the supply volt-amperes and supply power factor. Assumethat the converter is lossless.(d) Determine the rms value of the SCR current and the diode current.

Answered: Image /qna-images/answer/02e44b66-bb32-4a4e-9124-8a6ef415280a.jpg

Question 2. Considering this figure. The firing angle is 45°, the motor current is 10 A, and the supply voltage is 110 v. (a) Draw the waveforms of v, vo. io. isi, iDi, and i. (b) Determine the power taken by the de motor. 0₁ 0₂ (c) Determine the supply volt-amperes and supply power factor. Assume that the converter is lossless. (d) Determine the rms value of the SCR current and the diode current.

Question 2. Considering this figure. The firing angle is 45°, the motor current is 10 A, and the supply voltage is 110 v. (a) Draw the waveforms of v, vo. io. isi, iDi, and i. (b) Determine the power taken by the de motor. 0₁ 0₂ (c) Determine the supply volt-amperes and supply power factor. Assume that the converter is lossless. (d) Determine the rms value of the SCR current and the diode current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

D. a Hall effect generator. 7. When power to a resistance load is controlled by full-wave SCRs with a 90° firing angle, what is the load power factor? A. 0.87 B. 1.0 C. 0.71 D. 0
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 240 V (RMS), 50 Hz. The delay angles of both thyristors are set to 45 degrees. The maximum RMS and average current ratings of the thyristor are equal to: Select one: O a. 33.94A and 21.6A O b. None of these O c. 24A and 10.8A O d. 48A and 26.09A Clear my choice
A 220 V, 1 kW heater is fed from a single phase ac voltage controller using a thyristor in anti-parallel with a diode. If the firing angle is 45°, sketch the circuit and: a. Calculate the output voltage and current.b. Sketch the output voltage and current waveforms.c. Calculate the load power.d. Calculate the average current through the load
What is use of solenoid coil in the pressure to converter? a. To produce magnetic field in the LVDT b. To change the LVDT output c. To bring back the pivoted beam normal position d. To produce linear displacement in bellows
C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. C2 (ii). A sinusoidal waveform is displayed on a C.R.O. screen, the time/cm switch is on 40 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3 cm and the peak to peak distance is 5.6 cm. Determine the following: The frequency is The magnitude of the sine voltage is The amplitude is The R.M.S voltage is
Draw dc load line :
1. Impedance is the total opposition to an AC circuit caused by electric penalty tions, the tra capa multiple pacitive systema 62 Fundamentals of AC Electricity Questions for This C a. 1. Draw a diagram of an AC sine wave and identify its peak voltage and peak-to-peak voltage levels. b. 2. Explain the term frequency as it refers to AC electricity. c. 3. Discuss the difference between a load center and a fused disconnect. 2. WE wa 4. Explain how you would test for voltage in a fusible dis- connect on the line-side and load-side terminals. vi ci 5. Trace the path of a generated AC voltage from the generat- ing station where it is produced to the point where you would connect it to a machine in a factory. Be sure to iden- tify all the important parts of the system between the gen- eration station and the disconnect on the machine. a. be 3. True or False inductive reactance, capacitive reactance, and resistan 2. The units of impedance are
2 Compare between base load pbiney stvion and peak load power station.
Maz a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.3 milli seconds. Find D The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and 0 =40 degrees. on Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximnum value = a) (ii) Value of voltage at 2.1 ms = b) Angular frequency =
In a DC power supply unit if the final output is 20 V so the regulator used is: ----
h) Explain the methods of voltage control used in AC-AC converters.
B1. For the CRO square voltage waveform is shown in Figure. The time/cm' switch is on 2 ms/cm and the 'volts/cm' switch is on 20 V/cm. Calculate (a) the periodic time, (b) the peak to peak voltage, (c) the maximum voltage, (d) the time taken to complete half cycle. The periodic time The peak to peak voltage The maximum voltage The time taken to complete half cycle