Q,(B = 50) V, 20 V (unregulated) V. (regulated) 220 2 RL = 1 kN. %3D 12 V Figure 4 Q.4. (a) Analyze the circuit given in Figure 4 for the output voltage V. (b) Analyze the dissipated power in R, and state about maximum power rating of resistor R. (c) What happens to V, if Zener diode become open circuit.

Q,(B = 50) V, 20 V (unregulated) V. (regulated) 220 2 RL = 1 kN. %3D 12 V Figure 4 Q.4. (a) Analyze the circuit given in Figure 4 for the output voltage V. (b) Analyze the dissipated power in R, and state about maximum power rating of resistor R. (c) What happens to V, if Zener diode become open circuit.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

An ac voltage of peak value 20v is connected in series with a silicon diode and load resistance of 5002. if the forward resistance of diode is 102 find: i- Peak current through diode. ii- Peak output voltage. ii- What will be these values if the diode is assumed to be ideal (Vdiode =0)?
Discuss the effect of placing a bleeding resistor R1 in series with the Zener diode that is connected across the load resistor RL.
Consider the half-wave rectifier shown in the figure below. Let vs be a sinusoidal with 10V peak amplitude with frequency of 60Hz and let R = 1000 ohms. Use the contant voltage-drop diode model with VD = 0.7 V.
Given a single phase full wave rectifier shown in figure below, determine Is, Vs, efficiency, RF, TUF and the diode current rating. Assumed diode is Ideal. Is Vdc=100 V RL Vs ldeal, Idc=100 A
Q1/ a/Draw the output voltage waveform for the bridge rectifier in this figure : 5:1 D Da 120 V ms Dy RL B/ What PIV rating is required for the diodes in a bridge rectifier that produces an average output voltage of 50 V? Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with Izx = 1.5 mA and V, = 14 V. lllee 幸

For the circuit shown in Figure, consider Ideal diodes. If Vs = 19sin wt, Vb = 4 V, the minimum value of output voltage is: Vout at of estion Vs Vb Oa. -4 V Ob. -15 V Oc. -19 V Od. 4 V
Ex2: (H.W) For the 1-0 half wave rectifier circuit shown in Figure = 200 volt. Determine VLmean, ILmean, below, R = 100, V VSr.m.s' Vor.m.sorms FF and RF. Vs max = 200 V Diode www Vo R=1.5 K
1- Connect the Diode Characteristics circuit with a 800 resistor and anvariable AC input voltage source.2- Draw the readings on a V vs I curve and the two graphs look as followsForward bias and reverse bias graph.3- draw the output voltage cross the diode.4- Discuss the diode I-V characteristics curve
Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
1 Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage Ve-20 V and bias voltage VBi= 2.7 v. PP a) What is the function of the circuit . b) Draw the circuit diagram.
In the circuit shown in the figure, diode voltages are given as 0.6V and rD = 100 ohms. When point B is open circuit AIf + 5V is applied to the point of application, drawing the shape of the circuit formed and calculating the currents passing through the resistors.calculate.
A bridge rectifier circuit has secondary voltage of 12 V Assume secondary resistance and diode forward resistance to be negligible. Load resistance is 100(ohm.) Calculate peak load current, DC load current, rms current and across each diode.