Q5/ A downward force of (250 N) is applied to the small piston with a diameter of ( 75 cm) in the hydraulic lift system shown below upward exerted by the large piston with a diameter of ( 3m) mechanical advantage of hydraulic lift? c- If the input force of ( 250 N) pushes the small piston down by (2.5 m) . How high will the large piston rise? a- What is the b- What is the F1 F2

Q5/ A downward force of (250 N) is applied to the small piston with a diameter of ( 75 cm) in the hydraulic lift system shown below upward exerted by the large piston with a diameter of ( 3m) mechanical advantage of hydraulic lift? c- If the input force of ( 250 N) pushes the small piston down by (2.5 m) . How high will the large piston rise? a- What is the b- What is the F1 F2

Name: Q5/ A downward force of ( 250 N) is applied to the small piston with
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q5/ A downward force of ( 250 N) is applied to the small piston with adiameter of ( 75 cm) in the hydraulic lift system shown belowupward exerted by the large piston with a diameter of ( 3m)mechanical advantage of hydraulic lift? c- If the input for

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.113P: Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
A hydraulic lift uses an incompressible fluid to lift a 15 KN car. If the large cylinder's area is 25 times larger than the smaller one, 10. what is the minimum force required to lift the car?
The hydraulic jack in Fig. is fi lled with oil at 56 lbf/ft 3 .Neglecting the weight of the two pistons, what force F onthe handle is required to support the 2000-lbf weight forthis design?
A hydraulic press has a ram of 30 cm diameter and a plunger of 4.5 cm diameter. Find the weight lifted by the hydraulic press when the force applied at the plunger is 800 N
3m Q4/ Find the pressure force and position of center of pressure on a triangular plate of base 2m and height 3m which is immersed in water in such a way that the plane of the plate makes an angle of 60° with the free surface of the water. The base of the 2.5m 2m plate is parallel to the water surface and at a depth of 2.5m from water surface.
Q2) The figure below represents a hydraulic car jack has an output cylinder 30 cm in diameter and an input cylinder 5 cm in diameter and is filled with oil of density 900 kg/m 3. An automobile of mass 1200 kg needs to be clevated 35 cm. (a) How far does the piston of the input eylinder need to move? (b) What is the magnitude of the force on the input piston required to keep the car elevated? Input end 4,4, = A4, Output end up by a distance h, area A mass 14 initial initial position position area A Points (a) and down by a distance h, (b) are at the thị same level. fluid of density p,
Q3) Find the horizantal and vertical pressure force exerted on the gate (AB) of the tank. I [Tank length = 3.5 m). P=15kq Water r=2m
Rover weight capacity 35 kilo grams (payload)Rover measurements:Wheel distance - 14.5 inches and 8.5 inchesRover platform size (width & length) 14.4 inches x 10.4 inchesHeight- 15.8 inches Water tank selectionMore or less 25 liters*For tank selection we need to justify the size with the center of gravity, proving that is themaximum dimension or liters of the tank because the center of gravity will be higher makingthe rover prone to topplingPump selection*Our sprayer design has two nozzles which splits using a tee splitter, we need to find thesize of the pump to obtain the same discharge rate of a normal sprayer. A normal sprayerhas a 12V pump and a pressure from 0.2 to 0.45 mpa (30-65 psi)The application rate of the main pesticide is 9.6 - 19.2 fl oz/A (Brigade Insecticide for sweetpotato)Thai was the initial deign where the water tank is above the battery and pump, but wechanged our mind, now it is the battery and pump above the waterBattery selection* once the size of the pump…
Ex. 5. A weight lies on a piston with a radius r₂ = 1.0m. Determine the for- ce F₁ applied to the piston with radius r₁ = 20 cm if the hydraulic jack is in a balance. The jack is filled by an oil with po = 850 kg/m³. A mass of we- ight is m 1000 kg. Neglect the mass of the pistons. (Ans. F₁ = 392.4 N) = F₁ 0.3 m m oil
3- If F = 1x, F = xi, a = wk,, the centrifugal force is equal to a: mw²xî ------- b: -mw²xk c: mw²x k a: 4 d: -mw²xî e: None of them Ś
A vessel is filled with oil (ρoil = 900 kg/m3) up to 1 m of its height. It is 3m wide, 2m high and 10 m long.Find the following :A. The maximum horizontal acceleration that can be charged to the vessel without spilling anyoil.B. If this vessel is closed and is completely filled with oil and accelerated horizontally at a rate of 3 m /s2 .B.1. The total force acting at the rear wall and at the front wall of the vessel.B.2. The accelerating force on the fluid mass.