I need assistance in this problem 14-26. Water flows from a lake through a 300-m-long pipe having a diameter of 300 mm and a friction factorof f = 0.015. The flow from the pipe passes through a 60-mm-diameter nozzle and is used to drive the Peltonwheel, where the bucket deflection angles are 160o. Determine the power and torque produced when the wheelis turning under optimum conditions. Neglect minor losses.2 m20 mB

Answered: Image /qna-images/answer/80b37d36-e7f4-4cd9-99f3-d06d380ce9bc.jpg

Answered: Determine the power

Engineering

Mechanical Engineering

Determine the power

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Pelton wheel Is supplied with water under a head of 35 m at the rate of 40.5 klo litre/min. The bucket deflects the Jot through an angle of 160° and the mean bucket speed Is 13 m/s. Calculate the power and hydraulla efficiency of the turbine. w2 F Outlet 160° B
the buckets. The speed factor is 0.46. Neglecting any losses, determine: 360 m. The wheel is driven by two water jets at 400 rpm. The water spreads at 160° from Q1: A Pelton turbine of 85 % efficiency develops a power of 4500 kW under a head of (a) The water jet diameter. (b) The wheel diameter. (c) The wasted water energy.
pump supplies oil at 1.26 x 10 -3 m3/sec to a 50.8 mm diameter double-acting cylinder. If the applied force extending and retracting is 4.45 kN and the rod diameter is 25.4 mm. Determine the following; a. The hydraulic pressure during the extending stroke. b. The piston velocity during the extending stroke. c. The cylinder horse power during the extending stroke.
pump supplies oil at 1.26 x 10 -3 m3/sec to a 50.8 mm diameter double-acting cylinder. If the applied force extending and retracting is 4.45 kN and the rod diameter is 25.4 mm. Determine the following; a. The hydraulic pressure during the extending stroke. b. The piston velocity during the extending stroke. c. The cylinder horse power during the extending stroke. d. The hydraulic pressure during the retraction stroke e. The piston velocity during the retraction stroke. f. The cylinder horse power during the retraction stroke
7- Water to run a Pelton wheel is supplied by a penstock of length e and diameter D with a friction factor f (Figure 3). If the only losses associated with the flow in the penstock are due to pipe friction, shown that the maximum power output of the turbine occurs when the nozzle diameter, D1, is given by: Homework D D1 = (2fl/D)¹/4
A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is 3 times the velocity head in the 150-mm pipe and the loss of head from 2 to B is 20 times the velocity head in the 100- mm pipe. Compute the horsepower output of the pump and the pressure heads at 1 and 2 when the discharge 12 L/s. El 72 m Figure 4-10 150 mm Ø 100 mm Ø EI O A PUMP O - El -6 m 2
Q11 Design the duct system shown below using Equal friction method, and determine the fan power when the fan efficiency is 68%. The duct is circular. Take the velocity in the main duct AB equal to 7 m/s. Assume a dynamic loss coefficient of 0.5 in T fitting and 0.8 in elbow fitting. Given AB=BC= 10 m and BD = 25 m. C 1 m³/s (7 marks) A B 2 m³/s D
A compressor piston has a stroke of 380 mm and the clearance volume of 7% of the stroke volume. At the beginning of compression stroke the pressure of air is 0.99 bar. When the piston has travelled 260 mm from the begining of the compression stroke the delivery valves open and delivers air at 4 bar. Find the value of n, if the compression follows the law PVn = C.
A centrifugal pump develops a head of 16.8 m at 1500 rpm. Rated capacity is 0.015 m3/s. Determine the size of the impeller in mm if Øe=0.45.
1.The engine has a given capacity of 60kw, calculate the power requirement in a hydraulic system tool , to know that the engine is capable to support the hydraulic system if a pump delivers 110 liters per minute and the pressure is 227bar.2.If the area of A1 = 0.05 m˄2 and the area of A2 = 1.5 m˄2 , external input force F1 = 50 N, then the external output force F2 ?
QUESTION 3 The refrigeration plant onboard a fishing vessel maintain minus 20 °C in a fish storage hatch at a design ambient air temperature of 33 °C. The plant which rejects condenser heat to sea water at +22°C operates at evaporating and condensing temperatures of minus 20 °C and 30 °C respectively. It is fitted with a 4- cylinder R134a compressor having a bore of 100 mm, stroke 150 mm and speed 1500 rpm. Given that the suction gas superheat is 10 °C, condensate sub cooling is 10°C, volumetric efficiency of compressor is 80 % and discharge gas temperature 65°C, determine the following: (a) Power consumption. (b) Isentropic efficiency. (c) Cooling capacity. (d) Carnot efficiency of the plant.
A pump with an impeller diameter of 300 mm running at a speed of 2950 rev/min delivering 450 L/min of water at a head of 350 kPa is going to be replaced by a geometrically similar spare pump running at a speed of 1450 rev/min delivering the same flow rate and head. Determine the impeller size of the spare pump and the percentage increase (decrease) of power required for the spare pump. OL. 380.1 mm; a decrease of 61.33% OI., 380.1 mm; an increase of 38.77% I. 147.5 mm; an increase of 3.4% IV. 210.3 mm; a decrease of 83.1%