AT kg mnass is rests on a fri Iong ramp and compresses a k= 4000 N/m spring a distance of 5 cm. The ramps angle of incline varies from 10 to 50 degrees, in increments of 10 degrees. For each angle of incline, determine if the block will slide off the top end of the ramp after it is released from the Spring. Output each angle of incline and whether of not the block reaches the top of the ramp.

AT kg mnass is rests on a fri Iong ramp and compresses a k= 4000 N/m spring a distance of 5 cm. The ramps angle of incline varies from 10 to 50 degrees, in increments of 10 degrees. For each angle of incline, determine if the block will slide off the top end of the ramp after it is released from the Spring. Output each angle of incline and whether of not the block reaches the top of the ramp.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
Find the smallest distance d for which the hook will remain at rest when acted on by the force P. Neglect the weight of the hook, and assume that the vertical wall is frictionless.
Find the tension T in the cable when the 180-N force is applied to the pedal at E. Neglect friction and the weights of the parts.
Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
Problem: 1F the cable that is connected block A A with an acceleration to OF 0.6 mlr Detormine the passibte Force in Newton OF block B, given its mars as 20 kg. Given: a= 0.6ms MB= 20 kg Raqd: FB %3D %3D Datum B. Datum+ soln: 25p+ h+ SA =L
If the maximum length of the spring is 40 cm, what average friction force opposes the motion of the mass?
Khufra works at a spring factory and he was assigned to test a certain spring, whose constant is 50 N/m, attached to a 30-kg block in an incline (θ=30°). With the spring initially at equilibrium position, the block was pushed 0.5 meters up the incline by a 50-N external force applied parallel to the path. If the coefficient of kinetic friction is 0.5, determine the: a) normal force (in Newtons) b) work done by the spring (in Joules)
If there is n friction in the system, the Lagrange's equation will be based only on kinetic energy and protentional energy only. Select one: O True O False III O
0.8m 0.8m, 1.0m /0.&m 0.6m Title The spring has an unstretched length of 0.4m and a stiffness of 200N/m. The 3 kg slider and attached spring are released from rest at A and move in the vertical plane. (a) Compute the change in elastic potential energy from A to B. (b) Compute the change in gravitational potential energy from A to B. (c) Compute the velocity of the slider as it reaches B in the absence of friction.
A force is applied to a block to move it up a 30°incline. The incline is frictionless. If F = 65.0 N andM = 5.00 kg , what is the magnitude of the acceleration ofthe block?
A spring is such that a 5 -lb weight stretches it 6 in. The 5 -lb weight is attached, the spring reaches equilibrium, then the weight is pulled down 3 in. below the equilibrium point and started off with an upward velocity of 6ft/sec. Find an equation giving the position of the weight at all subsequent times
- H1. A wooden block of mass m is pushed over a floor in a straight line in the x direction with a constant velocity vo > 0. At time t = 0, when the block is at position x = 0, it is no longer pushed and the block experiences only a constant sliding friction force F in the negative x-direction until it comes to rest. (i) Write down the equation of motion of the block for t > 0. Calculate the time, t, at which the block comes to a stop and also find the distance, d, travelled by the block from the time when the pushing is stopped to the time when it comes to rest. (ii) Calculate the work done by the friction force from x = 0 to x = d, and then show that it is equal to the change in the kinetic energy of the block.