Q4) Water at the rate of 0.6 kg/s is forced through a smooth (3cm)-ID tube 16 m long.The inlet water temperature is 10 C, and the tube wall temperature is 15 C higher than the water temperature all along the length of the tube. What is the exit water temperature. k=0.585, Pr= 9.4, µ= 1.31x10*,p= 992kg/m³, CP= 4195 j/kg.

Q4) Water at the rate of 0.6 kg/s is forced through a smooth (3cm)-ID tube 16 m long.The inlet water temperature is 10 C, and the tube wall temperature is 15 C higher than the water temperature all along the length of the tube. What is the exit water temperature. k=0.585, Pr= 9.4, µ= 1.31x10*,p= 992kg/m³, CP= 4195 j/kg.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

Water flows at a rate of 0.1 kg/s in a tube with a diameter of 250 mm. The tube is heated uniformly at a rate of 135 kW/m2. Find the wall temperature at a location where Tsat = 180 C and x = 25%. [Ans.: Ts = 188 C]
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the % of pressure drop? (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the value of G in kg/s.m2?. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
Flow Characteristics( Entrance Effect) Why was there some disagrement between the actual Pitot tube velocity profile and the power law velocity profile?
Q2:A) Define the bulk temperature (Tn), and prove that : T₁, - 2 ur dr B) Ethylene glycol flows at 0.01 kg/s through a 3 mm diameter, thin walled_tube. The tube is coiled and submerged in a well-stirred water bath maintained at 25 °C. If the fluid enters the tube at 85 °C, what heat rate and tube length are required for the fluid to leave at 35 °C ? At 60 °C, μ = 0.00522 kg/m.s, k = 0.26 W/m.K, C, 2562 J/kg.K. -
* Hot air enters a sheet metal đuct located in a basement. Determine the exit temperature and the rate of heat loss. Taking k 0.02735 W/m. C, v= 1.797x10 m'/s. Pr 0.7228, C-1007 J/kg.C ,pD MSc. Rasha Nasser 106 1.092 kg/m' H= 2.325 kg/m.s and e = 0.3 Ans: 45.1 °C, 2622 W Air dust 20 cm - 20 em Air L-12 m
48. Water is flowing in a smooth pipe of diameter D. A section of this pipe hav- ing a length of L is heated. Water at the inlet to the heated section has a tempera- ture of Tŋ. Water temperature at the exit of the heated section is Tp. The heated section of the pipe wall is maintained at a constant heat flux so that a constant temperature difference of AT, = T, – T, exists between the wall and the bulk wa- ter temperature. Show that for turbulent flow in the pipe and a specified heated length and pipe diameter, water temperature at the exit of the heated section is given by: 402 0.6 Pr T52 =Tf +0.0876 L AT DO.8 0.2 m
Flow Characteristics (Entrance Effect) -Why is the Δ P/ L Line extrapolated to the tube entrance for the calculation of the entrance loss coefficient, KL ?
A thick-walled cylinder tubing of hard rubber having an inside radius of 20mm is being used as temporary cooling coil in a bath. Ice water is flowing rapidly through inside tube and the inside wall temperature is 274.9K. The outside surface temperature is 297.1K. A total of 14.65W must be removed from the bath by cooling coil. How many m of tubing are required?
QS: Water at 15.56°C i to be heated in a 2-mm-ID tube until the exit temperature reaches 26.67+C. The tube wall temperature is maintained at 48.99-C and the inlet flow velocity is 0.3 m/s. Calculate the length of tube required in meters to accomplish this heating. Also calculate the total heating required, expressed in watts. Answers: L=0.13 m
derive the navier stoke equation to Vz (in function r) in a cylindrical pipe with the maksimum radius of a and L as the length of the pipe in a laminar and steady flow
. Oil enters a 1.25-cm diameter,3-m long tube at 38°C. The tube wall is maintained at 66°C, and flow velocity is 0.3 m/s. What is the total heat transfer to the oil and oil exit temperature? Assume an exit temperature of 50°C. Temperature (°C) p(kg/m³) u (kg/m sec) Cp J/hg °C) k(W/m °C) 0.210 0.0725 0.0320 40 0.144 867.05 864.04 1964 60 2047 0.140 80 852.02 2131 0.138