Q3- Air flows from a reservoir and enters a uniform pipe with a diameter of 0.05 m and length of 10 m. The air exits to the atmosphere. The following conditions prevail at the exit: P2 = 1bar, temperature T2 = 27°C and M2 = 0.9. Assume that the average friction factor to be f = 0.004 and that the flow from the reservoir up to the pipe inlet is essentially isentrópic Estimate the total temperature and total pressure in the reservoir under the Fanno flow model. %3D M2 0.9 D-0.05 m] L=10 m Po=! To=?C T2-27°C P2=1 Bar]

Q3- Air flows from a reservoir and enters a uniform pipe with a diameter of 0.05 m and length of 10 m. The air exits to the atmosphere. The following conditions prevail at the exit: P2 = 1bar, temperature T2 = 27°C and M2 = 0.9. Assume that the average friction factor to be f = 0.004 and that the flow from the reservoir up to the pipe inlet is essentially isentrópic Estimate the total temperature and total pressure in the reservoir under the Fanno flow model. %3D M2 0.9 D-0.05 m] L=10 m Po=! To=?C T2-27°C P2=1 Bar]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cylindrical tank in Fig. is being filled with water at20 ° C by a pump developing an exit pressure of 175 kPa. At theinstant shown, the air pressure is 110 kPa and H = 35 cm. Thepump stops when it can no longer raise the water pressure. Forisothermal air compression, estimate H at that time.
I need help on this question: According to the question: a) If the pipe connected to the pump inlet has a diameter of 24 mm with length (LCP) of 5 m and Darcy friction factor of 0.03, what would be the actual head rise across the pump for a case where the pump outlet pressure is 200 kPa? The difference in height between pump inlet and outlet is 0.25 m, the tank exit is sharp-edged, and the water level in the tank to the tank exit pipe (HWL) is 2 m. Also, consider that the flow velocity inside the tank is negligible. The value of the actual head rise across the pump is = ? b) What would be the pump motor power if the efficiency is 60%? The value of the pump motor power is = ?
When passing through an adiabatic turbine (figure), bullet steam at 500 °C and 3.5 MPa expands to 200 °C and 0.3 MPa, it flows at a flow rate of 529 oz/s, what is the power Specified by the turbine in kW if the piping at the same inlet is D1 = 5.90 in diameter and at the outlet, D2 = 0.82 ft in diameter? Data: for steam at initial conditions Hi = 3450.9 kJ/kg at final conditions, H2 = 2865.6 kJ kg; Specific volume of steam in the initial condition = 0.0992 m²/kg; Specific steam volume in the final condition = 0.7163 m/kg. %3! %3D
Problem (6.1) Steam at 1.8 MPa and 275 °C expands through a convergent- divergent nozzle to 0.1 MPa. If there is 10 % loss in energy between the throat and the nozzle exit and the vapor flow rate is 0.5 kg/s, determine the cross- sectional area of the throat and the nozzle exit.
S CE - Oil is transported from A to B along a pipe of constant diameter. The pipe is inclined at 50° to the horizontal and B is at the higher elevation. Considering the flow from A to B, which statement is correct? O The pressure head is decreasing and the velocity head is increasing. O The pressure head is increasing and the velocity head is decreasing. O The pressure head and velocity head are both increasing. O The pressure head is decreasing and the velocity head is constant. O The pressure head and velocity head are both decreasing. P Type here to search 0022 10°C Sunny AG A Q0 ENG 16/02/2022 DELL Esc F6 FB num 2 4€ E R Y F G J K ck D %23 B N M end V page page up ctri alt gr alt
Q1) Find: (a) inlet temperature (T1 =?), (b) mass flow rate of R-134a ((m =?), (c) exit diameter (D2 =?), (d) the rate of heat transferred to the surroundings (Qout =? ). P2 = 1MPA T, = 70°C Y2 = 70 (- Compressor W in = 100 (W) R-134a P = 500KP. Qout (sat. vapor)(1) m Y1 = 20 ( D = 0.5 (cm)
The environmental conditions of a nozzle are required to provide 100 kPa, 20 C values and R-134a constant flow at 200 m / s. Bowl efficiency can be accepted as 90 percent. What should be the pressure and temperature at the nozzle entrance?
Solve it correctly please. I will rate accordingly.
I need the answer as soon as possible
Mnot D Thot = 75°C Tout-? mcold Tcold = 18°C Hot and cold stream of water are mixing together as shown in Figure. The temperature of the hot and cold streams at the inlet are 75 °C and 18 °C, respectively. Mass flow rates of the hot and the cold streams are (1.500x10^-1) kg and (1.00x10^-1) kg, respectively. Find the temperature of the mixed stream. The specific heat of the hot water stream is 4000 J/kg- K and the cold stream is 3800 J/kg-K. Answer should be in °C with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible.
Energy balance. The flow rate of water is 0.021 m'/s through a 355-m long, 11-cm-diameter pipe (shown below and not to scale). The turbine that has an efficiency of 82% is used to recover the potential energy and generate power. Both reservoirs are very very large and contain water at 8°C. The roughness of the galvanized iron pipe is 0.14 mm. Problem 2 105 m 42 m What is the turbine output, i.e., how much usable power can obtained from the turbine?
Q#2 Air is flowing through a venture-meter whose diameter is 2.6 in at the entrance part (location 1) and 1.8 in at the throat (location 2). The gage pressure is measured to be 12.2 psia at the entrance and 11.8 psia at the throat. Neglecting frictional effects, show that the volume flow rate can be expressed as 2(P - P2) v = Ar p(1 – AIA}) and determine the flow rate of air. Take the air density to be 0.075 lbm/ft3. 12.2 psia 11.8 psia Air 2.6 in 1.8 in