Q4: For a 98 wt% Fe-2 wt% C at a temperature 700 °C, determine the following: a) The Number and types of The Phases Present. b) The Amount Of Phases Present in Grams That forms per 100 G. c)Draw The Microstructure Of Phases Present At This Point And What is The React called? d) Specify the following on Iron- Carbon Phase Diagram: (y+ L) phase, Eutectoid Reaction

Q4: For a 98 wt% Fe-2 wt% C at a temperature 700 °C, determine the following: a) The Number and types of The Phases Present. b) The Amount Of Phases Present in Grams That forms per 100 G. c)Draw The Microstructure Of Phases Present At This Point And What is The React called? d) Specify the following on Iron- Carbon Phase Diagram: (y+ L) phase, Eutectoid Reaction

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

According to the following graph, two samples of 1080 steel are cooled from the eutectoid temperature, one at a cooling rate of 250°C/s and the other at a cooling rate of 7.27x10-8 °C/s. Specify the phases obtained and explain their formation from thermodynamic and kinetic perspectives. Also, briefly describe their formation. Draw the microstructure of the phases obtained. Sıcaklık (C) 800 700 600 500 400 300 200 100 0 10 1 T M(başlama) M(% 50) M(% 90) 10 M+O -Otektoid Sıcaklık 10² Zaman (s) % 50 10³ 104 105
1. Specify all temperature-compositicn points at which eutectics, eutectoids and peritectics. At 700 degrees Celsius and composition of 20% by weight of copper, calculate the compositions by fraction of each phase for copper? 1700 1500 L. 1300 1100 900 TiCu- 700 Ti:Cu4 500 20 40 60 (Ti) Composition (wt% Cu) to (0o) anjesedwa
An alloy system consists of two metals A&B which are soluble in each other in all proportions in the liquid state, but completely insoluble in the solid state. The melting point of metal A is 425°C and B is 375°C. The lowest melting point (Eutectic) is 230°C at 40%B. Choose the correct answers for the following sentences: the phases present in the equilibrium diagram are: OL& A & B O A & B O A&L B& L
1. Given the time-temperature transformation diagram, what would be the phases present for a 1.13 wt. % C steel with no alloying elements. calculate the amount of pro eutectoid product, where applicable (at the bottom) A) quenched in cold water to 650 C in 0.1 seconds, then held at 650 C for 5 seconds, then quenched to 400 C, held at 400C for 60 seconds, and finally quenched to room temperature B. Necessary Steel Phase Diagram Calculations to determine the amount of pro eutectoid product:
None
Figure 2 refers to the phase diagram for silver and tin. Label the regions (1) to (5) Temperature, 0/°C 1000 800 600 400 200 0 Liquid 2 Ag,Sn 60 a 20 40 80 Mass percentage Ag/% 100 Question 6: What will be observed when liquids of composition of 40% Ag are cooled to 200 K? When will it begin to precipitate? When will it become solid?
Referring to Figure 1, please answer the following [NOTE: SHOW YOUR WORK on Figure 1]:a. provide the specific name for the phase boundary lines denoted by A and B. b. identify the phases present at equilibrium in the phase fields denoted by C, D, and E. c. identify the specific name for the point denoted by F. d. What is the maximum solid solubility of Mg in Al? At what temperature does it occur? e. An Al-Mg alloy (10 wt% Mg, 90 wt% Al) is heated slowly (to insure equilibrium) from a temperature of 200 C: i. At what temperature does the first liquid phase form? ii. What is the composition of the liquid phase at the temperature in part i.? iii. At what temperature does complete melting (no solid phase remaining) occur? iv. What is the composition of the last solid remaining prior to complete melting? f. Using the equilibrium phase diagram of Figure 1, identify the phases present, their compositions, and their relative mass fractions at equilibrium for a 70 wt% Mg – 30 wt% Al…
An alloy consisting of completely soluble cadmium (Cd) and zinc (Zn) in the liquid state, but neither of them dissolves in each other in the solid state. the table shown below shows the solidification temperatures for various alloys of cadmium and zinc. 1. Draw the equilibrium diagram according to the information given and data in the table and indicating all important temperature and phases. 2. Find the percentage of each phases and percentage of constituents of the alloy that contain 60 % Zn and at a temperature 300 °C. 3. Find the melting point for the following alloys 20 % Cd, 80% Cd 4. Draw the internal structure, noting the phases of the following alloys A) 30 % Cd at 290 °C b) 60 % Cd at room temperature. % of Zinc in alloy Start of solidification ("C) End of solidification ("C) 0 10 14 20 30 40 50 60 321 290 266 275 293 310 328 345 70 80 90 100 362 390 401 419 266 266 266 266 266 266 266 266 266 266 266 266
the PCS containing 0.4%C was quenched hardened in water, amd tempered at 400oC. sketch and identify the phases of the microstructure pf the stell at rhe following states a) above the upper critical point just before quenching in water b) after quenching I’m water prior to tempering C) after tempering
A hypothetical eutectic phase diagram for metals A and B shows that cooling a liquid melt with a concentration of 50 wt% A-50 wt% B to just below 625 °C (eutectic isotherm temperature) results in simultaneous formation of alpha and beta phases. The phase diagram also shows that alpha (A rich) and beta (B rich) phases exist at left and right extremes of the phase diagram, respectively. At the eutectic isotherm temperature, the maximum solubility of B in A and A in B is 10 wt% and 5 wt%, respectively. The phase diagram does not have any intermetallic compounds. A new solid alloy is made by melting together 86 gr of a 40 wt% A-60 wt% B alloy with 136 gr of 65 wt% A-35 wt% B alloy followed by cooling the melt to 400 °C. If the new alloy is heated up from 400 °C to just below 625 °C, answer the following questions: a. Calculate the overall alloy composition. b. Determine phases present and calculate their respective masses. Calculate the masses of the primary phase, eutectic phase, and…
700 L 600 M a + L Mg, Pb 500 P 465 400 L Mg Pb 300 200 a + Mg Pb B+ Mg Pb 100 20 40 60 80 100 Mg Composition (wt% Pb) Pb Mg,Pb Using the above figure, sketch neatly the microstructure of the alloys (given in the below table) and determine the amount of each phase presented. Structure of the alloys at different compositions 田 Compositions &temperature 10%Pb,90%Mg Structure Structure Compositions &temperature 20%Pb, 80%Mg @400°C @0°C My.Pb 50%Pb,50%Mg 67%Pb, 33%Mg @0°C Mgz PB @0°C 81%Pb,19%Mg 90%Pb,10%Mg @200°C @0°C Temperature ("C)
A 10 30 70 1) For an A-B alloy of composition 25 wt% B (i) Draw the microstructure at T (just above the eutectoid temperature) and calculate the fraction of each phase in the microstructure. (ii) Draw the microstructure at T (just below the eutectoid temperature) and determine the amount of each phase, i.e., fraction of proeutectoid alpha, eutectoid alpha and eutectoid beta. 2) Provide a brief summary of phase transformations which are often observed in the iron-carbon alloy system due to various heat treatment procedures carried out to tune the microstructure. Compare mechanical strength and ductility of the materials/microstructures that form as a result of such heat treatment processes.