Q3. The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thickness of the flanges and determine the angle of twist of end C of the shaft relative to end D. The shaft is subjected to a torque of T Nm. The material is steel. d 25 mm 6 mm T A D 150 mm. B 225 mm 150 mm.

Q3. The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thickness of the flanges and determine the angle of twist of end C of the shaft relative to end D. The shaft is subjected to a torque of T Nm. The material is steel. d 25 mm 6 mm T A D 150 mm. B 225 mm 150 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flexural member is fabricated from two flange plates 1/2x16 and a web plate 1/4x20, thusforming a built-up ‘I’ shape member. The yield stress of the steel is 50 ksi.a. Compute the plastic section modulus Z and the plastic moment Mp with respect to the majoraxis.b. Compute the section modulus S and the plastic moment My with respect to the major axis
The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thíckness of the flanges. The shaft is subjected to a torque of T = 1000 N. m. The material is A-36 steel, G = 75 GPa (Figure 1) Part A Determine the angle of twist of end C of the shaft relative to end D. Express your answer using three significant figures. ΑΣφ vec $C|D = 0.0542 rad Submit Previous Answers Request Answer Figure X Incorrect; Try Again; 4 attempts remaining
The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thickness of the flanges. The shaft is subjected to a torque of T = 1000 N. m. The material is A-36 steel, G = 75 GPa (Figure 1) Part A Determine the angle of twist of end C of the shaft relative to end D. Express your answer using three significant figures. vec ? $C/D = 0.100 rad Submit Previous Answers Request Answer Figure 1 of 1 X Incorrect; Try Again; 5 attempts remaining ( Return to Assignment Provide Feedback 25 mm 75 mm 6 mm A 150 mm. 225 mm 1150 mm. 圓
The horizontal bar ABC is supported by a pin at A and two rods with identical cross- sectional areas. The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the force in each rod when the force P = 80 kN is applied. Use Est = 200 GPa and Eal = 70 GPa. %3D Steel Aluminum A B T2 m- 1.5 m- Im
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.
The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a 304 stainless steel rod EF having a diameter of 40 mm, and a rigid member G. If the supports at A, C, and F each have a stiffness of k= 200 MN/m determine the average normal stress developed in the rods when the load is applied. A C -300 mm- 30 mm 30 mm B D G E 450 mm 40 kN 40 kN 40 mm F
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 50 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.7 ksi. Brass segment (2) has an outside diameter of 0.85 in., a wall thickness of 0.13 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.0 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 45 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.6 ksi. Brass segment (2) has an outside diameter of 0.80 in., a wall thickness of 0.14 in., a length of L2 = 32 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.2 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.06 in., a length of L₂ = 24 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ (1) TB B L2 (2)
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.0 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.13 in., a length of L₂ = 28 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. y L₁ L2 TB. X (1) (2) N Answer: (a) TB = (b) T₁ = T₂= (c) DB = lb-ft lb-ft lb-ft rad B C
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.90 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.6 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.06 in., a length of L2 = 20 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.4 ksi. Determine: (a) the allowable torque Tg that can be applied to the compound shaft at flange B (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque T.