6.83 The span of a cantilever beam is 2 m. The cross- section of the beam is a hollow square with external sides 100 mm; and its / = 4 x 105 mm². The safe bending stress for the beam material is 100 N/mm². The safe concentrated load at the free end would be

6.83 The span of a cantilever beam is 2 m. The cross- section of the beam is a hollow square with external sides 100 mm; and its / = 4 x 105 mm². The safe bending stress for the beam material is 100 N/mm². The safe concentrated load at the free end would be

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

/ Determine the maximum Bending stress at ciny location alang the beam? 500 200 700 N/m 30 300nm Comm 30 ntine stresses
Bending Stress in Beam A symmetrical l-section is 200 mm deep and its moment of inertia about centroidal axis is 50x106 mm4. If the bending stress is limited to 100 N/mm² then bending moment it can resist will be
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
O FS = 2.4 O FS = 2.2 Consider a simple supported beam subjected to the load shown. The beam has a solid square cross-section with edge "a", and made of steel alloy having a yielding tensile and compressive strength of oy = 400 MPa. Determine its minimum required edge "a" for a factor of safety against yielding FS = 2.5. The area moment of inertia of that section about its neutral axis N.A. is INA = b.h³/12. of 3 kN 2 kN/m D 6 m + Select one: 5:37 PM 86°F Light rain ENG 6/18/2021 hp
Solve this
3
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN
Experts Pleae help ASAP
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 520 mm?. If the stress in the bar must not exceed 650 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 8 m, b = 4.8 m, and c= 10.4 m. (1) B' a Answer: P = i kN
Determine the stress in each member of the truss shown. Get first the value of RAv then Find the value of member AE @ Joint A
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.
A cantilever beam of length 6 m has an additional support at a distance of 2 m from its free end as shown in Figure 4. It has the cross-sectional dimensions with height h=300 mm, inside height h₁ =250 mm, width b= 150 mm, and inside width b₁=100 mm. It is made of an elastic perfectly plastic material having tensile and compressive yield stress of oy = 250 MPa. Determine the yield moment My of the beam Determine the plastic moment Mp of the beam ✓ By using force method and selecting the vertical reaction at C to be redundant, draw shear and bending diagrams using the graphical method. -Determine the minimum value of W at which collapse occurs B/2W C 77 2m 2m 2m C b₁