The shown L-shape cantilver is loaded as shown and fixed at A. It has a constant section of 40 mm X 20 mm. For point I located at 50 mm from support A, at the midheight of the section, determine the principal stresses, the principal planes and the maximum shear stress. Y 50 mm 150 mm 40 mm 0.5 kN I B 20 mm 3 kN 160 mm 2.5 kN

The shown L-shape cantilver is loaded as shown and fixed at A. It has a constant section of 40 mm X 20 mm. For point I located at 50 mm from support A, at the midheight of the section, determine the principal stresses, the principal planes and the maximum shear stress. Y 50 mm 150 mm 40 mm 0.5 kN I B 20 mm 3 kN 160 mm 2.5 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Activity 3 Questions WHAT'S YOUR SCORE? Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 5º. Use G = 80 GPa for steel. (Note: Two values of P are to be compared here). 300 mm 500 mm
Determine the number of main bars, spacing, and determine the spacing for stirrups.
The strain at point A on the bracket has components €g = 330 (10-6), e, = 560 (10-6), Yxy = -570 (10-6), e; = 0. Correct Part B Determine the maximum shear strain in the x - y plane. = 6.15x10-4 'in-plane Submit Previous Answers Correct Part C Determine the absolute maximum shear strain. (Figure 1) Figure < 1 of 1 vec -4 Yaa = 7.99 • 10 max Submit Previous Answers Request Answer X Incorrect; Try Again
Torialai Stan Problem 1-- Short link BD consists of a single steel bar 40 mm wide and 12 mm thick. Knowing that = Call 100 Mpa, determine: a) The maximum value of the normal stress in the link BD b) The required pin diameter at support D. 20kN 100 150 mm 300 mm D 30
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
1. Answer Set A only
Detailed Solution please
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.
Q4: determine the maximum tensile and compressive stresses acting normal to the beam. 50 mm 10 kN 100 mm 30 kN 6 m 2m B (2
2. Two 115-mm wide by 15-mm thick steel plates are welded as shown. The load P = 135 kN is concentrically applied and B= 25°. For the xy directions shown, determine a) b) The normal stress or acting perpendicular to the weld; The shear stress try' acting parallel to the weld; Sketch the state of stress to represent results from a) and b) above. В P 2² 115 mm. P
If the shaft is subjected to a uniform distributed torque of , determine the maximum shear stress developed in the shaft. The shaft is fixed at A and C. 400 mm 20 kN-m/m 600 mm 80 mm 60 mm Section a-a
#2 will upvote anyone who will answer