Q3: You have been asked to choose a pump that can provide 105 ft head for 4000 gpm flow. The table below gives the pump curve data for a pump operating at 1000 rpm and has 3-in. impeller. The available pumps had different impeller diameter D and rotation speed N as shown below. Which pump can satisfy the required flow and head and which pump cannot? Use your own word to explain the reasons behind your decision? Standard Pump Flow (gpm) Head (ft) Pump 1 Pump 2 | Pump 3 N (rpm) D (in) 800 900 750 80 4 4 5 500 75 1000 73 1500 70 2000 67 2500 62 3000 58 3500 52

Q3: You have been asked to choose a pump that can provide 105 ft head for 4000 gpm flow. The table below gives the pump curve data for a pump operating at 1000 rpm and has 3-in. impeller. The available pumps had different impeller diameter D and rotation speed N as shown below. Which pump can satisfy the required flow and head and which pump cannot? Use your own word to explain the reasons behind your decision? Standard Pump Flow (gpm) Head (ft) Pump 1 Pump 2 | Pump 3 N (rpm) D (in) 800 900 750 80 4 4 5 500 75 1000 73 1500 70 2000 67 2500 62 3000 58 3500 52

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The width of the channel is reduced in the downstream. Upstream flow is subcritical. Please can you explain possible changes to the flow of the channel, and show how this would look on the specific energy diagram? Thanks for any help! Ive attached a picture of the specific energy diagram.
Water is to be moved from one large reservoir to another at a higher elevation as indicated in figure shown The loss of available energy associated with 2.5 ft^3/s being pumped from sections 1 to 2 is 120 times of the velocity head. Determine the amount of shaft power required. Section (2) Bn inside diarmeter pipe 3D I 500 Section (1) Pump Select the correct response 1.14 hp 1.28 hp 1.07 hp 1.56 hp
Make computations of a ramp pump where the Source Elevation = 50 meters. Target User Elevation = 85 meters. Target output = 230 Liters/min
Q/Suppose there are three identical pumps in series, each producing 1500 ft of the head at flow rate 1000 gpm capacity, and another case there are three pumps in series that have differing heads of 1500 ft, 1200 fi, and 1400 ft at 1000 gpm, Find the total head and flow rate generated and discuss the different if conneet parallel ?
I need the answer as soon as possible
I need the answer as soon as possible
Using the pump selection table below to determine the best pump for the given condition: 20 Imp.g.p.m 100 • A flow of 0.01 m³ /s and a head of 25 m 20 US.g-p.m 200 s 0 100 100-80/32 100-65/32 300 65–40/32 80-50/32 100-80/26 125-100/26 12 5-40/265-50/26 80-65/26 100 50-32/25- 1-100/20 100-80/20 (ft) 5-50/2080-65/20 65-40/20 50-32/20 100-80/16 80-85/16 65-50/16 (m) s0-32/16- 65-40/16 80-65/13 S-0/13 65-50/13 40–32/13 20 2900r/min 14 14 nyh Q L/s 12 50 200 s0 * O 100 15 125-100/16 ..
please answer all questions ans i will give a thumbs up
If you don't know the solution please leave it but don't give me wrong solutions
A. For the system shown in the figure, select the proper pump that has the best efficiency to raise 12 m³ of water from the lower tank to the upper one. The time targeted for the process to be completed at least in 60 mins. The pump is located at zero elevation. Make your calculations at the minimum allowed depth in the lower tank (i.e. 1 m). What would be the efficiency and actual flow rate? Head (m) 35 30 25 20 15 B. Using your recommended pump, how long does it take the pump to elevate 12 m³ if the water level in the lower tank is fixed at 3 m. 40 10 5 0 - 0 Pump 3 Pump 2 Pump 1 0.001 Max: +3 m 0.002 Min: +1 m I I 60% 70% 80% 90% T I 1 I I + T 1 I I + I CHw = 150 D = 100 mm 0.003 Flow (m³/s) T I I + 1 T L=10 m +16 m 0.004 L = 16 m ooo oo ロロ 0.005 0.006
Calculate the Hydraulic HP, efficiency for this pump, the number of stages, and the HP required using pump characteristic curves for the given data, for: > Flow Rate=750 bbl/day > Depth 3500 ft > Specific gravity of the Fluid (sp.gr.) =1.0 dimension less Head Fect Motor Pumр Load Only Eff hp 30.0 25.0 50% 20.0 40% 15.0 30% 10.0 0.20 20% 5.0 0.10 10% 250 500 750 1000 1250 1500 Capacity - Barrels per Day
How long would it take a pump delivering 25 gal/min to extend a 5-in cylinder with a 30-in stroke?