Given the pump curve below, what will be the flow rate and head added for three of these pumps is operating in parallel and each pump is operating at point 2? Standard System 1200 3 hp 900 2 600 300 0 2 4 6 8 10 12 14 16 GPM Feet of Head (TDH)

Given the pump curve below, what will be the flow rate and head added for three of these pumps is operating in parallel and each pump is operating at point 2? Standard System 1200 3 hp 900 2 600 300 0 2 4 6 8 10 12 14 16 GPM Feet of Head (TDH)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

it is generally recommended that pump operation should be maintained within +/- O 10 % of the best-efficiency point (BEP) flow rate. O 25 30 O 50 Pump curves relate head, hp. added by the pump and the flow rate, Q, through the pump. For commercial-size pumps, the curve also typically includes all of the following except O efficiency O NPSHR O power O NPSHA Placing two pumps in parallel will achieve which one of the following? Move the pump performance curve up Move the pump performance curve to the left Move the pump performance curve to the right Move the pump performance curve down Placing two pumps in series will achieve which one of the following? Move the pump performance curve to the right Move the pump performance curve up Move the pump performance curve to the left Move the pump performance curve down Partially closing a valve on a pipe attached to a pump will change which one of the following? pump curve system curve static head not enough information
Problem 7 - 64 Determine the flow in each pipe in the figure shown and the elevation of reservoir Cif the inflow to reservoir A is 515 Lit/sec. L El. ? C El. 90 m El. 90 m D 300m - 450 mm t= 0.03 El. 80 m 600m - 600 mm t-0.025 300m - 450 mm f0.03 900m- 450 mm 600m - 450 mm Fx 0.03
Q5) The following data were collected for two verticals in a stream at a gauging station. Compute the discharge in the elemental strips by (i) the mid-section method (ii) the mean-section method Distance from Depth, d Immersion of current meter опe end of (т) below water surface (m) water surface at 0.2d at 0.8d (m) rev sec rev sec 0.8 135 150 97 151 1.2 150 100 150 138 Rating equation of the current meter; v= 0.7 N+0.03 where N= rev./sec, v = velocity (m/sec).
The volume of discharge at a specific gauging station were recorded and tabulated below. The gauge height at zero discharge was determined to be h_o=20.8m. (i) Develop the stage discharge relationship in equation form. (ii) Calculate for the discharge that corresponds to the stage of 2675 m3/s and 2725m3/s.
Q2- Water ( p= 990 kg/m' & µ= 0.001 pa.s) is pumping from a water tank to water injection well with carbon steel pipe at the same level, where the pipe diameter is 12 inch, pipe length is 4700 m, pipe roughness is 0.0000045 m, and water flow rate is 0.0065 m/sec. 1- Calculate discharge frictional head loss. 2- Calculate pump liquid power, if pump section head value is 3.8 m.
Certain Pump delivers water in a 150 millimeter diameter smooth pipe & 240 meter long to a hydrant to which it is connected a line cotton rubber-lined firehose 60 millimeter diameter. If flow is 16 L/s, at what velocity must it be maintained on the discharge side of the pump?
Find out the approximate flow in the pipes in the network shown Fig. Q. 4(c). 5 lps+ 20 Ips+ 40m-200mm dia 60m-150mm dia in 40m-150mm dia an noters1201 50 lps 30m-150mm dia 60m-150mm dia 30m-100mm dia 10 lps 10 lps 60m-150mm dia 5 lps
SITUATION 2 (For this situation, there are no choices but you can input your answers in google forms later) Calculate the following if the amount of flow is 1.26m³/s, the 80% efficient pump delivers 1073kW, and the turbine is 92% efficient. EL. 120.50 C-110 0.60m-diameter 360m EL 77.90 C-110 0.60mdiameter 45.60m P 556m 14. Compute for the energy given by the pump 15. Total Head Loss
DT. Asmaa Abdul Jabbar Q2: Water flow from B to A, if real power of pump =175kw, with efficiency 85%. (neglect minor losses) Find: Discharge at each pipe. Pipe No. L (km) D (cm) f 0.018 1 0.5 15 2 0.55 20 0.02 EL.25m A P 1 2 EL.100m B
With the given pipe lengths, sizes and connections and if all pipes have an f=0.020, determine the flow in each pipe if the total head loss between A and D is 150 ft. 3250 ft of 12 in Situation 6: 2 2750 ft of 21 in 2250 ft of 10 in 4750 ft of 27 in A 1+ B C 5 D 3 2750 ft of 14 in 4 -
A water tank is 30 ft in diameter and the normal depth is 25 t. The outlet is a 3-in horizontal pipe at the bottom a if this pipe is sheared off close to the tank, what is the initial flow rate of water from the tank? (Neglect hiction less stub of pipe) How long will it take for the tank to be empty?
100mmgl 个一 680mm 320 mm I320m 300mm A H2O A vertical venturi meter 100mm diameter is installed in a 300mm diameter vertical pipe as shown. The flow is upward. If the specific gravity of the mercury at the bottom part of the manometer is 13.6, determine the a) Discharge neglecting head loss, b) Discharge if head loss from point 1 to point 2 is 500mm, and c) Coefficient of discharge (This is a multiple answer question. You must have 3 selected choices since there are 3 required answers in the problem) A No answer among the choices in question A B No answer among the choices in question C C = 0.819 D No answer among the choices in question B E) Q = 70.3 L/s Qt = 86.2 L/s G) Qt = 65.8 L/s H) Q = 86.2 L/s Q = 65.8 L/s C = 0.936 к) с30.753 Qt = 70.3 L/s M) C = 0.668 N) Qt = 57.6 L/s o Q = 57.6 L/s