Part 4Evaluate the friction factor.ft3Write the Reynolds number as function of the volume flowrate Q in. (Use 2 significant digits on coefficients. Do not enter units as a part of your response.)Re=Part 5Evaluate the friction factorWhat is the relative roughness for the pipe?E/D-Part 6Evaluate the system curve for the pump.(a) Calculate values for the pump head at volume flowrates of 100, 140, 160, and 200 gal/min.Q-100 gal/min hp-Q-140 gal/min hp-Q-160 gal/min hp-ftftftQ-200 gal/min h₂-ft(b) After plotting the system curve on the pump performance characteristics by using the values calculated for pump head as a function of volume flowrate, find the volume flowrate in gal/min for maximum efficiency for a 7.5-in-diameter pump impeller.Q-gal/min(c) What is the pump head associated with these conditions?h₂-ft Part 1Part 2Part 3hpA centrifugal pump having a 7.5-in-diameter impeller and the characteristics shown in the figure below is to be used to pump gasoline through 4000 ft of commercial steel 3-in.-diameter pipe. The pipe connects two reservoirs having open surfaces at the same elevation. Determine the flowrate. Do you think this pump is a good choice? This figure isreferred to as the pump performance characteristics.5008 in. dia400 7出3006Head, ft2001006560555040 bhp30252080°40120 160 200 240 280 320Capacity, gal/minWrite the system equation for this flow system as function of the friction factor f and volume flowrate Q in gal/min. (Use 2 significant digits on coefficients. Do not enter units as a part of your response.)

the coefficient of friction (f) is a dimensionless quantity used to describe the frictional…

Answered: Evaluate the friction factor. Write the…

Evaluate the friction factor. Write the Reynolds number as function of the volume flowrate Qin (Use 2 significant digits on coefficients. Do not enter units as a part of your response.) Re=

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A laboratory has installed a double-suction, three-stage, centrifugalpump with a discharge of 330 gpm under 200 ft head and running at 1200 rpm. It isproposed to install another pump with double suction and six stages, but of the samecharacteristics, to operate at 98 ft head and deliver 430 gpm. Calculate a) the speed ofthe proposed pump; b) the impeller diameter of the proposed pump if the diameter of theexisting pump is 6 inches; and c) the type of the existing and the proposed pump.
Question 5: For system shown below, estimate: 1. The head, flow rate, and efficiency in case of combined pumps in parallel and series 2. At which configuration should the system be operated? 3. In case pump 2 is turned-off, estimate the shut-off head and free delivery flow rate in the system 20 Hp (m) 40 100 80 60 -Pump 2 Pump 1 Efficiency curve 100 200 Combined in series Combined in parallel 300 Eff. 90% 80% 70% 60% 50% 40% 30% 400 Q(L/min)
You need to pump water at a rate of 9,200 GPM to an elevation of 76 feet through 2,200 LF of DIP (CHw = 120). You have a 42 HP pump that is rated at 88% efficiency. What size pipe, from the choices below, would you recommend? 6 inch 10 inch 14 inch 18 inch 24 inch
A fire hose nozzle has a diameter of 1.125 in. According to some fire codes, the nozzle must be capable of delivering at least 250 2.750-in.-diameter hose, what pressure must be maintained just upstream of the nozzle to deliver gal/min. If the nozzle is attached to a this flowrate? Answer p= i psig
Methanol (SG = 0.8335, viscosity is equal to that of water) is being transported from a very large reservoir and is entering at a standard 1.25-in 540 pipe at an absolute pressure of 14.7 psia. The methanol is transported at a total of 1450 ft and passes through 15 standard ells, 5 gate valves (open), 6 tees (standard), and 4 tees (as ell, entering branch). The methanol is discharged 22 ft above the inlet at a gauge pressure of 8 psig. If the fluid flows at a rate of 30 gpm and the pump have an efficiency of 50%, calculate the actual power needed in kW.
Non-positive displacement pump is the type of pump whose size is lesser for a given discharge räte. Select one O True O False
Determine the shaft horsepower for an 80% efficient pump to discharge 30L/s through the system. The system losses, exclusive of pump losses, are 12V2/2g and H = 16m. Ans: 8.75hp H 150mm dia
it is generally recommended that pump operation should be maintained within +/- O 10 % of the best-efficiency point (BEP) flow rate. O 25 30 O 50 Pump curves relate head, hp. added by the pump and the flow rate, Q, through the pump. For commercial-size pumps, the curve also typically includes all of the following except O efficiency O NPSHR O power O NPSHA Placing two pumps in parallel will achieve which one of the following? Move the pump performance curve up Move the pump performance curve to the left Move the pump performance curve to the right Move the pump performance curve down Placing two pumps in series will achieve which one of the following? Move the pump performance curve to the right Move the pump performance curve up Move the pump performance curve to the left Move the pump performance curve down Partially closing a valve on a pipe attached to a pump will change which one of the following? pump curve system curve static head not enough information
a. Calculate the pump head b. Plot the EGL and HGL for the system
A centrifugal pump having a head-capacity relationship given by the pump curve equation h₂ = 180 - 6.10 × 104 Q², with ha in feet when Q is in gpm, is to be used with the system shown in the figure. For Z2 - Z₁ = 50 ft, what is the expected flowrate if the total length of constant diameter pipe is 600 ft and the fluid is water? Assume the pipe diameter to be 4 in. and the friction factor to be equal to 0.02. Neglect all minor losses. (2) (1) Pump 22
The mechanical efficiency of the pump is 0.85 and pumping with a rate of 650 gal/min of engine oil at 100° with the following properties: specific gravity of 0.883 and kinematic viscosity 21.9x10-6. The 6-in and 4-in Schedule 40 pipe has an area of 0.2006 ft² and 0.0884 ft², respectively. Determine the power added by the pump. Flow Pump 6-in Schedule 40 4-in Schedule 40 | 4 in Engine Oil 30 in Mercury (sg =13.54)
Water is to be moved from one large reservoir to another at a higher elevation as indicated in figure shown The loss of available energy associated with 2.5 ft^3/s being pumped from sections 1 to 2 is 120 times of the velocity head. Determine the amount of shaft power required. Section (2) Bn inside diarmeter pipe 3D I 500 Section (1) Pump Select the correct response 1.14 hp 1.28 hp 1.07 hp 1.56 hp