Q3: A single stage, double acting air compressor running at 1000 rev./min delivers air at 25 bar and 170°C For this purpose, the induction air conditions can be taken as 1.013 bar and 15°C, and The air deliver at rate 0.25 m³/min. The clearance volume is 3% of the swept volume and the stroke bore ratio is 1.2/1. Calculate the bore and stroke, the volumetric efficiency, the indicated power, and the isothermal efficiency.

Q3: A single stage, double acting air compressor running at 1000 rev./min delivers air at 25 bar and 170°C For this purpose, the induction air conditions can be taken as 1.013 bar and 15°C, and The air deliver at rate 0.25 m³/min. The clearance volume is 3% of the swept volume and the stroke bore ratio is 1.2/1. Calculate the bore and stroke, the volumetric efficiency, the indicated power, and the isothermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single cylinder petrol engine works on the Otto cycle and draws in air at 1.01 bar and 22°C. The bore and stroke of the engine are 105 mm and 130mm respectively and the clearance volume is 13% of the swept volume. If the maximum temperature in the cycle is 1400°C find; a. The Volume at the remaining points of the Cycle b. The Heat Supplied, Heat Rejected, & Efficiency of the Cycle c. The mean effective pressure
Give: Otto cycle Compression ratio = 9 Intake air is at 100kpa and 20°C Maximum cylinder volume = 500 cm^3 Temperature at the end of the adiabatic compression = 800 K CP = 1.01kJ/kgk, Cv = 0.718 kJ/kg, k = 1.4, R = 287.1 J/kgk m= 0.000595 T3 = 1926
Solve both please
3. A single acting reciprocating compressor is needed to compress 100 kg of air per hour from 100 kPa and 25 deg Cintake condition to 900 kPa delivering pressure. The compression is expected to follow PV to the power 1.25 = C. If the compressor has a clearance factor of 4% and it is expected to operate at 300 rpm, what is the required piston displacement?
Answer carefully please. Step by step solution thank you
a. Assume a blower operating at 4000 rpm compressing air from 68°F and 14.7psia to 8.5psig, handling 16000cfm at the design point with an efficiency of 70%. It is desired to find the operating conditions (BHP, H and Q) at 3600 rpm. b. Same as problem (a) except assume that the speed and inlet temperature remains the same, but the inlet pressure at the point considered, drops to 10psia. c. Same as problem (a) except assume that the speed and inlet pressure remains the same, but the inlet temperature rises to 100°F.
Give: Otto cycle Compression ratio = 9 Intake air is at 100kpa and 20°C Maximum cylinder volume = 500 cm^3 Temperature at the end of the adiabatic compression = 800 K CP = 1.01kJ/kgk, Cv = 0.718 kJ/kg, k = 1.4, R = 287.1 J/kgk T4 = 800 K
9.2 The inlet stagnation temperature of a centrifugal compressor rotating at 10,000 rpm is 20°C. The inlet flow is axial and the blades are radially tipped at the exit. It is required to produce a stagnation pressure ratio of 2.8 when the total to total effi- ciency is 0.85. It has 19 blades and a mass flow rate of 3.0 kg/s. Through measure- ments, the density of air at the exit of the impeller is found to be 1.5 kg/m³. The width of the blades at the exit is 1 cm. Calculate the following: (a) power required to drive the compressor, (b) diameter of the impeller, and (c) absolute Mach num- ber at the exit. Use Stanitz's equation for the slip coefficient. Ans: 355 kW; 0.694 m; 0.897
A The compression ratio of a diesel cycle is 15.5, and the cutoff occurs at 10% of the stroke.14 psia and 600 K characterize state 1. Calculate the following for the hot-air standard with k= 1.34and a starting volume of 2 cu ft:a. Find T2 , P2 , V2 , T3 , V3 , P4 , and T4b. Compute the heat added (QA),heat rejected (QR), work (W) andthe cycle efficiency (e).c. for a rate of circulation of 1000 cfm,compute the horsepower.
A The compression ratio of a diesel cycle is 15.5, and the cutoff occurs at 10% of the stroke. 14 psia and 600 K characterize state 1. Calculate the following for the hot-air standard with k= 1.34 and a starting volume of 2 cu ft:a. Find T2 , P2 , V2 , T3 , V3 , P4 , and T4b. Compute the heat added (QA), heat rejected (QR), work (W) and the cycle efficiency (e).c. for a rate of circulation of 1000 cfm, compute the horsepower
I only need help with filling in the answers for parts h and i. At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. The maximum temperature in the cycle is 2250 K and the compression ratio is 9.8. The engine has 4 cylinders and an engine displacement of Vd = 2.1 L. Determine per cylinder: a) the volume at state 1.b) the air mass per cycle.c) the heat addition per cycle, in kJ.d) the heat rejection per cycle, in kJ.e) the net work per cycle, in kJ.f) the thermal efficiency in %.g) the mean effective pressure, in bar.h) Develop a full exergy accounting per cycle, in kJ. Let T0 = 300 K, p0 = 1 bar (See image below).i) Devise and evaluate the exergetic efficiency for the cycle. part h
A single stage single acting reciprocating air compressor has 0.25 m x 1.75 m runs in 750 rpm is to deliver 0.20m³ free air per second from 101.3 kPa to 355 kPa. Calculate (a) the volume displacement (b) the volumetric efficiency (c) the isothermal work done, compression is at pV =c (d) the isothermal compressor efficiency if the the indicated power of compressor is 40kW