Q2.) The cable supports a uniform load of 920 N/m. The lowest point of the cable is 1.2 m below points C and D. The cable is supported by a truss on either side made of three truss members. Supports A and F are pin supports and B and E are roller supports. Neglect the mass of the truss members. (a) Determine the maximum tension along the flexible cable. (b) Determine the axial loads in truss members DF and DE and state whether each member is in tension or compression. 3.2 m 1 A 2.4 m- 920 N/m 6 m 2.4 m- 3.2 m

Q2.) The cable supports a uniform load of 920 N/m. The lowest point of the cable is 1.2 m below points C and D. The cable is supported by a truss on either side made of three truss members. Supports A and F are pin supports and B and E are roller supports. Neglect the mass of the truss members. (a) Determine the maximum tension along the flexible cable. (b) Determine the axial loads in truss members DF and DE and state whether each member is in tension or compression. 3.2 m 1 A 2.4 m- 920 N/m 6 m 2.4 m- 3.2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B •5-13. Determine the horizontal and vertical com nents of reaction at C and the tension in the cable AB t the truss 30 2 m 3 kN 4 kN 2 m 2 m 2 m
The frame ACD is supported by ball-and-socket joints at A and D and by a cable that passes through a ring at B and is attached to hook at G and H. Knowing that the frame supports at point C a load magnitude P = 125 N and weighs 35 N, center of gravity at C, determine the tension in the cable. 0.35 m 0,875 m G H 0.925 m 0.75 m D A 0.75 m В 0.5 m C 0.5 m
The trusses are pin connected at B and suspended fromn the parabolic cable. Note: the unit of the force, k means kips or kilopound. Deterrmine the following: 1. Minimum tension in the parabolic cable 2. Vertical reaction at pin B 3. maximum force/tension in the parabolic cable D E 14 ft 6 ft K 4. 16 ft F GH B 4 k 5 k -4 @ 12 ft 48 ft- 4 @ 12 ft 48 ft-
Cable CB supports a load uniformly distributed along the horizontal as shown. The lowest point C is located 9 m to the right of A. Determine: (Minimum Tension in Newton) (the vertical distance a) (Maximum Tension at A in Newton)
Three loads are suspended as shown from the cable ABCDE. Knowing that dc = 3 m, determine the sag at DB
The two-member frame is pin connected at E. The cable is attached to D, passes over the smooth peg at C, and supports the 500-N load. Determine the horizontal and vertical reactions at each pin.
The homogeneous bar AB weighs 550 N. End B lean against a rough vertical surface and end A is supported by a ball-and-socket joint. Determine the reaction at A and B of the tension in the cable is 150 N. Z. C 30° В 5 m 6 m --- 4 m X A y
6-98. The two-member frame is pin connected at E. The cable is attached to D, passes over the smooth peg at C, and supports the 500-N load. Determine the horizontal and vertical reactions at each pin. 0.5 m 0.5 m 1 m 1m B 0.5 m D 500 N
The uniform rod AB has a mass of 40 kg. Determine the force in the cable when the rod is in the position shown. There is a smooth collar at A.
Catenary cable (different level of support) The uniform cable weighing 11.25 N/m is suspended from points A and B. The force in the cable at B is shown to be 375 N. A. Determine the tension at A. B. Determine the horizontal distance between A and B. C. Determine the length of the cable
The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB is 8.9 kN. Determine the required tension T in cable AC such that the net effect of the two cables is a downward force at point A. Determine the magnitude R of this downward force. Assume a = 30 m, b = 41 m, c = 29 m, and d = 35 m. B A b C
The beams AB and BC are supported by the cable that has a parabolic shape. See figure below. D 3 m 3m F 9 m B 3 kN ,5 kN m 2 m 2 m 2m 2 m 2 m 2m 2 m تمع What is the tension at E? What is the vertical reaction at B?