4. Determine the service load capacity of 2C10X20 channels as a truss member attached to a 7/8 in gusset plate as shown in Figure e5.20. The steel is A572 Grade 65 and the 7/8 in diameter A325 bolts are in a bearing-type connection (A325- X) with no threads in the shear planes. The load is 25% dead load and 75% live load O O O O O 4@3-1-0 O C10 x 20

4. Determine the service load capacity of 2C10X20 channels as a truss member attached to a 7/8 in gusset plate as shown in Figure e5.20. The steel is A572 Grade 65 and the 7/8 in diameter A325 bolts are in a bearing-type connection (A325- X) with no threads in the shear planes. The load is 25% dead load and 75% live load O O O O O 4@3-1-0 O C10 x 20

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.4.3P

See similar textbooks

Similar questions

4. The tension member shown below is a C 310 x 30.8 of A572M gr 345 steel materials. Will it safely support a service dead load of 265 kN and a service live load of 555 kN. L 50 102.5 102.5 50 65 65 65 O O 22 veny diameter bolts C310 x 30.8 Iso A36M stool matorial and select a double anglo tonsion member to rosist
Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in the plane of shear. The plates 3/8 x 7 and 5/16 x 7 are made of A36 (F,=58 ksi) steel. If live load to dead load ratio is 4, find the maximum service load that the connection can carry. A325X % in diameter bolts PL 3/8 x 7 PL 5/16 x 7 1.5 in 2 in 2 in 1.5 in 1.5 in 2 in 2 in 1.5 in
Q14 What is the available tensile strength of a WT 20x74.5 made of A572 grade 50 steel? Use ASD, assume a shear lag factor (U) of 0.75, the connections are welded, and neglect block shear or other Chapter J requirements. Check both yielding and rupture. a) 800 kips b) 986 kips c) 533kips d) 656 kips
A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of nominal diameter 1/2 in in a zig-zag arrangement as shown. Determine the tensile strength capacity Pu of the connection. Review the three limit-states: (a) yielding in the gross area, (b) rup- ture in the overall net tensile area, and (c) block shear strength.
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 1/2" thick Gusset Plate 3/8" thick 2" 3" 2" 2" 3" 3" 2"
= 410 N/mm? 8.20 A column section ISHB 300 @ 618 N/m (f, mand f, = 250 N/mm") is to be spliced. The factored design loads are: %3D Axial load over the column 450 kN Shear force 100 kN Bending moment (a) Design the splice plates and bolted connections using bolts of grade 4.6. (b) Design HSFG bolts and revise the splice plate size if possible. 30 kNm
5) Calculate P the allowable tensile load for the butt joint shown. Each A325-N high-strength bolt has a diameter of 0.9 inches. The plates are made of ASTM A36 steel. If the applied load is 200 kips, is this connection adequate? If not, what needs to be changed so that this connection can handle an applied load of 200 kips? P- ФФ P ! 12"x " P. P.
1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts. The steel is A36. Compute the following: 130 mm 25 mm 0 0 a) The design strength for LFRD. b) The allowable strength for ASD. 25 mm CIVIL ENGINEERING STEEL DESIGN
2-PL10x1/2 A-36 Bolts are 7/8 in A-325, threads are not excluded. All edge spacings are minimum | 3" | 3" | о PL 10x3/4 A-572Gr50 a) Determine the nominal bolt capacity. b) Determine the nominal bearing capacity for each plate. c) Determine the nominal rupture capacity of each plate. d) What is the nominal capacity of the connection? e) Using LRFD, is this connection capable of supporting a dead load of 150 kip and a live load of 100 kip?
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 2" 3" 2" 1/2" thick Gusset Plate O 2" 3" 3" 2" 3/8" thick P
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for tension on gross area in kip? Express your answer in two decimal places. 1/2" thick Gusset Plate 3/8" thick 2" 3" 2" 2" 3" 3" 2" P.