Q2. A concentric annulus tube has inner and outer diameters of 25 mm and 100 mm, respectively. Liquid water flows at a mass flow rate of 0.05 kg/s through the annulus with the inlet and outlet mean temperatures of 20°C and 80°C, respectively. The inner tube wall is maintained with a constant surface temperature of 120°C, while the outer tube surface is insulated. Determine the length of the concentric annulus tube. Assume flow is fully developed. T, Insulation Water

Q2. A concentric annulus tube has inner and outer diameters of 25 mm and 100 mm, respectively. Liquid water flows at a mass flow rate of 0.05 kg/s through the annulus with the inlet and outlet mean temperatures of 20°C and 80°C, respectively. The inner tube wall is maintained with a constant surface temperature of 120°C, while the outer tube surface is insulated. Determine the length of the concentric annulus tube. Assume flow is fully developed. T, Insulation Water

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the heat transfer coefficient for a single 5-cm-OD, 60-cm-long tube in cross-flow. The temperature of the tube surface is , the velocity of the fluid flowing perpendicular to the tube axis is 6 m/s, and the temperature of the fluid is . Consider the following fluids: (a) air, (b) hydrogen, and (c) water.
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
Air at 1 atm and 20 C flows in a 2.5-cm-diameter tube. The maximum velocity (m/s) of air to keep the flow laminar is
Milk is Pasteurized by first heating it to 71oC, and keeping it at that temperature for 17 seconds before cooing it rapidly for bottling. Fresh milk at 5oC enters the Pasteurization unit where it flows through a thin-walled stainless steel (SS) tube of 2.0 cm diameter. The inside surface of the tube is such that the flow is turbulent to promote good mixing and uniform temperature across the flow at every point along the tube. Heating is provided by passing the tube in a closed container that is filled with saturated steam at atmospheric pressure and 100oC. Hence, we can assume that the thin-walled SS tube temperature is maintained at 100oC all along its length by condensing steam over the outside surface. The flow-rate of milk is 40kg per minute (i.e. approximately 10 gallons per minute). a) What is the mean velocity (m/s) and ??? for the milk flowing through the tube between 1-2? b) What is the convective heat transfer coefficient h (W/m2K) over the inside surface of the tube? c) What…
Liquid ammonia is transported from a production plant to a processing center via a 0.6-m diameter pipeline at a mass flow rate of 0.15 kg/s. Surface temperature of the pipe is maintained 0°C by using a cooling jacket with ice-cold water. Ammonia enters the pipeline at -17°C and exits at -3°C. Assume the flow is both hydrodynamically and thermally fully developed in the pipe. What is the length of the pipe? 185.7m
Determine the expected Fanning friction factor for water at 28 degrees Celsius flowing through a smooth tube whose ID is 15mm, at a velocity of 0.45 m/s
A liquid metal flows at a mass rate of 3 kg/s through a constant heat flux 5-cm-i.d tube in a nuclear reactor. The fluid at 473 K is to be heated with the tube wall 30 K above the fluid temperature. Determine the length of the tube required for a 1-K rise in bulk fluid temperature, using the following properties: p = 7.7 x 10^3 kg/m^3v = 8.0 x 10^-8 m^2/sCp = 130 J/(kg K)k = 12 W/mKPr = 0.011 Kaufman's correlation: Nu = 0,625.(Re.Pr)0,4
150 L/s of hot air at 80 degrees Ceelsius enters an 8m long uninsulated square duct of cross-section 20 cm x 20 cm and leaves at 70 degree Celsius. The outer surface temperature of duct is observed to be constant. Use Colburn Equation.
Glycerin passes through a pipe of 30 mm inside diameter at a mass flow rate of 700 kg / hr. The wall of the 2.5 m heating section of the pipe is kept constant at 115 ° C. The glycerin inlet temperature is given as 15C. What is the exit temperature of glycerin from the pipe?