Kailasben The device is used to measure a change in temperature. BarsAB and CD are made of A-36 steel and 2014-T6 aluminumalloy respectively. When the temperature is at 70° F, ACE is inthe horizontal position.Figure1.5 in.-0.25 in.B3 in.< 1 of 1JuulumbulPart ADetermine the vertical displacement of the pointer at E when the temperature rises to 160 ° F.(Figure 1)Express your answer with the appropriate units.SE =SubmitOValueProvide FeedbackUnitsSwPrevious Answers Request Answer?X Incorrect; Try Again; 5 attempts remaining

Answered: Image /qna-images/answer/14fceea3-89b8-4e04-8c09-d17f2fd14ed0.jpg

The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy respectively. When the temperature is at 70° F, ACE is in the horizontal position. Figure 1.5 in. -0.25 in.-- 3 in. 1 of 1 ululaul Y Part A Determine the vertical displacement of the pointer at E when the temperature rises to 160° F. (Figure 1) Express your answer with the appropriate units. SE = Submit LO HÅ Value Provide Feedback Units Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining

The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy respectively. When the temperature is at 70° F, ACE is in the horizontal position. Figure 1.5 in. -0.25 in.-- 3 in. 1 of 1 ululaul Y Part A Determine the vertical displacement of the pointer at E when the temperature rises to 160° F. (Figure 1) Express your answer with the appropriate units. SE = Submit LO HÅ Value Provide Feedback Units Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

9. One of the following is a glass disk that fits in a microscope eyepiece that has a ruled scale, which is used to measure the size of magnified objects: A. Optical flats B. Optical projector C. Ocular lens scale D. Industrial magnifiers E. Shup microscope
12
help[
Determine the absolute maximum shear stress of the stress state acting on the element shown in the following figure. 120 Mpa 300 Mpa 50 Мра
Pls see instructions in the attached image.
Find lx and ly.. Urgent...please do in 15 minute's
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Te-Learning Portal Courses Reports e-Services Which of the following statement is correct Select one: of O Fiction is very bad at rough surfaces ion O Friction is zero for smooth surfaces O Friction is good at smooth surfaces O Friction is high for rough surfaces
Speed
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Project is a program designed to user application that may be simple .or complex True False O
In the last few steps, where did 0.4 come from?