2. Design a half-bridge dc-dc converter with a centered-tap output transformer with the following specifications: VIN=480V, Vo=240V@lo=20A, fs=75kHz and a maximum peak-to-peak output ripple of 1%. Your design should include the following: a) steady-state duty cycle, b) transformer turns ratio, c) output inductor value, and d) output capacitor value

2. Design a half-bridge dc-dc converter with a centered-tap output transformer with the following specifications: VIN=480V, Vo=240V@lo=20A, fs=75kHz and a maximum peak-to-peak output ripple of 1%. Your design should include the following: a) steady-state duty cycle, b) transformer turns ratio, c) output inductor value, and d) output capacitor value

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(a)Design a forward converter to produce an output voltage of 30V when the input dc voltage is unregulated and varies from 150V to 175V. The output power varies from 20W to 50W. The duty ratio of the switch is varied to compensate for the fluctuations in the input dc source to regulate the output voltage at 30V. Specify: the switching frequency and range of required duty ratio of the switch, ii. the turns ratios of the transformer, i. the value of L, and iv. the capacitance required to limit the output ripple to less than 0.2%. Your design MUST work for all operating conditions.
Design a flyback converter for an input of 24 V and output of 40 W at 40V. Specify the transformer turns and magnetizing inductance, switching frequency and capacitor to limit the ripple voltage less than 0.5%.
Part 1) Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is resistive with R=10 Ohms. The critical value of L and the critical value of C are equal to: a. 0.625mH and 0.392uF b. 0.625mH and 0.196uF c. 0.312mH and 0.196uF d. None of these Part2) Now consider the same given but the load is an inductive load with R=10 Ohms and L=10 mH. The switch is ideal. Calculate The RMS load current Io and the RMS converter current Ir are equal to: Select one: a. 5A and 3.54A b. None of these c. 8A and 5.66A d. 12.5A and 8.84A
You are required to design a DC power supply using the following isolated DC-DC converter. The load is a resistive load with R= 110. The duty cycle of the converter is 40% and the Mosfet (s) switching frequency is 100 kHz. The input voltage is 20 V and the output voltage is 5 V. The ratio between primary and secondary turns of transformer is 1: n. Design the value of transformer turns ratio n under the CCM operation. I2 D 1:n EVout LM Vin
Derive the average and rms values of output voltages and currents for three phase semi converter. Power Electronics
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di i v2 = VmSin ot RL Vs(N V1 Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V None of the above ell ell
4: Design a buck converter to produce an output voltage of 18 V across a 10-_ load resistor. The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the rms current in the inductor and capacitor. Assume ideal components.
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230v (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di v: = VmSin ot Vs V. + Vy = VSin ot D2 Full-wave rectifier. Circuit operation during positive half cycle ell + ミ」
A load consists of XL=70 and XC=150 are connected in parallel across 120 Volt supply.The reactive power of the circuit is.......
a) Draw the basic topology of a buck converter. b) Design a buck converter to produce an output voltage of 18 V across a 10 2 load resistor. The output voltage ripple must not exceed 0.5 percent. The de supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the rms current in the inductor and capacitor. Assume ideal components.
1. Single phase half-wave converter has a purely resistive load of R and delay angle is a= n/2 determine: (a) Rectification efficiency (b) Form factor (c) Ripple factor.
In the full-wave rectifier circuit of figure , the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 23oV (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di V2 = VmSin cot Vs (N Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V O None of the above ell ell