Q2: Find the present survivability index (PSI) of a road section has area of 1000 sq.ft. If its condition; rutting= 0.5 in, cracks length=50 ft., and Patching area= 5 sq. ft. PSI = 5.03 – log(1+ SV) – 1.38(RD)² - 0.01(C + P)/2 SV = («3); - n-1 To find the slope variances (SV), use the following table. 0.0 -0.01 Yi 3.68 0.4 -3.3 0.81 2.2 -0.42 -3.35 3.02 where ;n = number of intervals

Q2: Find the present survivability index (PSI) of a road section has area of 1000 sq.ft. If its condition; rutting= 0.5 in, cracks length=50 ft., and Patching area= 5 sq. ft. PSI = 5.03 – log(1+ SV) – 1.38(RD)² - 0.01(C + P)/2 SV = («3); - n-1 To find the slope variances (SV), use the following table. 0.0 -0.01 Yi 3.68 0.4 -3.3 0.81 2.2 -0.42 -3.35 3.02 where ;n = number of intervals

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1: In construction of a highway section, the earthwork information is available as shown in the table below. The free-haul distance is 500m and the swelling factor is 20%. Draw the mass haul diagram between station 3 + 00 and station 9 + 00 and determine the extra compensation that must be paid to the contractor when the overhaul price is $200/m3 station. Station Cut Fill 3 + 00 50 250 4 + 00 150 550 6+ 00 150 200 7+ 00 910 50 9 + 00
Fluid mechanics
Q1. Geologists investigating a landslide surveyed the elevation of a hillside and found it to be 872 m at the bottom and 991 m at the top. The survey points were horizontally separated by 465 m. How steep is this hillside as a percent grade if 45 degrees is a 100 percent grade? percent grade = ........... % Q2. Enter your answer in scientific notation. The discharge (Q) of a stream is the velocity (v) times the cross-sectional area (A): Q = vA. What is the discharge of a stream with a velocity of 2.1 m/s and a cross-sectional area of 54.2 m2? Q = ........ × 102 m^3/s
needed asap pls, thank you
Determine the fracture type of reinforced concrete beams, whose cross section and properties are given below. and calculate the load-bearing moments.
Following figure shows the mass-haul diagram for a road project. -Mass-Haul Diagram Volume (m³) 20000 15000 10000 5000 0 -5000 -10000 -15000 -20000 0 500 1000 1500 2000 Distance from the start of the project (m) 2500 O The soil will have to be moved from right towards the left ● Cannot be determined from the given information O The soil will have to be moved from left towards the right. O There will not be any movement of soil. 3000 3500 The section from 1400 m to 1600 m has been identified as a free-haul section. What will be the direction of net soil movement within this free-haul section?
Please give a more detailed and correct solution with question C. The embankment for a highway 5097 ft long, 104 ft wide and 6 ft in compacted thickness is to be constructed from a sandy soil trucked from a borrow pit. The water content of the sandy soil in the borrow pit is 6.748% and its porosity is 0.422. The specification requires the embankment be compacted to a dry unit weight of 122.874 lb/ft3. The specific gravity is 2.588. Determine the following: a. Total weight of the soil solids, kips. b. Total volume of the soil required from the borrow pit, ft3. c. Weight of water to be added per foot length of the embankment to reach 10% moisture content, lb.Round off answers to three decimal places.
In a separate region of the new E-W highway proposed by the Maine DOT an 18 ft. highway embankment will be constructed and overly a 10 ft thick layer of soft clay. The embankment will be compacted with an undrained strength of 800 psf and the soft clay has a measured strength of 450 psf. The DOT would like to maintain a factor of safety of at least 1.5. a. Draw the critical failure service and compute the factor of safety using the Swedish method and solution charts from DM7.1 (handouts in class) H= 18 ft Soft Clay Su = 450 psf 7 = 120 pcf Hard, competent material N.T.S Roadway Clay Fill Su = 800 psf 7 = 120 pcf D = 10 ft
I need the answer as soon as possible
Road The most potential mass-wasting hazard exist here is Select one: Oa. slump O b. rock fall O c avalanche Od rock slide O e creep
Question 4 a) The axle load data collected on a section of a highway for a short duration for 2 and 3 - axle trucks are presented in Table 1. Determine the ESAL per axle, total ESAL per truck and the truck factors for 2 and 3-axle trucks. Table 1: Axle load data Vehicle питber No. of axles Axle Weight (tons) Axle 3 Axle 4 Axle 5 Date Сommodity Axle 1 Axle 2 15-Jul-10 GR 6687 -10 16-Jul-10 GW 4925 S 15-Jul-10 AS 4602 Z 15-Jul-10 BA 4772 C 16-Jul-10 GR 2706 09 15-Jul-10 GR 9626 E 16-Jul-10 WR 9290 C 15-Jul-10 AS 6865 Q charcoal 3 4.00 10.20 5.20 13.60 16.80 cement 5.50 lumber 10.20 4.00 14.60 charcoal charcoal charcoal 2 6.10 4.20 14.20 8.50 19.80 13.20 charcoal 5.10 13.70 charcoal 8.40 14.90 6.10
1.What are railway design subgrade parameters