Question 1:- Design the overlay with the help of following data: (i) Mean 1.0 mm, standard deviation = 0.25 mm (ii) at Temperature the time measurement=38°C of (iii) soil type= clay (iv) Design traffic at the end of 10 years is 1000 cvpd (v) Coverage of the deflection values on pavement = 98% Question 2:- Determine the thickness of rigid overlay for a 10 cm thick slab in good condition. The design thickness required, due to increased ased loading, is 20 cm

Question 1:- Design the overlay with the help of following data: (i) Mean 1.0 mm, standard deviation = 0.25 mm (ii) at Temperature the time measurement=38°C of (iii) soil type= clay (iv) Design traffic at the end of 10 years is 1000 cvpd (v) Coverage of the deflection values on pavement = 98% Question 2:- Determine the thickness of rigid overlay for a 10 cm thick slab in good condition. The design thickness required, due to increased ased loading, is 20 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A soil nail proposed to be installed under the conditions given below is designed against unfactored working force of 50KN. • Ground described as sandy gravel. • Soil nail installed at an angle of 10 degrees to the horizontal and 1.2 m below the ground surface. • Nail dimensions: total length = 5 m with 60% bonded, bonded diameter = 0.35 m, debonded diameter = 0.15 m Assuming parameters not given and considering the water able to be at the surface, propose the suitable type of soil nail and calculate the theoretical working factor of safety of the installed nail against pull out. Also, briefly discuss what would jeopardise your theoretical predictions of the nail performance.
ANSWER CORECTLY AND PROIVIDE FBD AND DETAILED SOLUTION
Uniformly graded aggregate gradations have missing particles of one or more sizes. True False
1. What is the effective net area in square inches? 2. What is the available tensile rupture strength in kips? 3. What is the available strength in kips? 4. What is the nominal available tensile rupture strength in kips? Pls answer within 30 mins ty
Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A and B are tested to failure in tension. (a) At failure the distances between the gage marks are LAf 2.90 in. and LBf 2.22 in.; the corresponding diameters at the failure cross sections are dAf 0.263 in. and dBf 0.471 in., respectively. Determine the percent elongation in 2 in. and the percent reduction in area for these two materials, and classify each material as either brittle or ductile. (b) From these tensile tests the following data are also obtained: EA 10.0 103 ksi, (Y)A 5 ksi, (U)A 13 ksi; EB 10.4 103 ksi, (Y)B 73 ksi, (U)B 83 ksi. From the data given here, make rough sketches (to scale) of the stress-strain diagrams of materials A and B.
choose the correct answer When the transient gradient is decreased from the No. 200 sieve of the bevel filler, a type shift occurs A- From lowest to highest B- From high to low C - It does not affect the type
compute the finesnnes and average of the cement
Project Location Description Sample No. CALIFORNIA BEARING RATIO (CBR) TEST Penetration Penetration (in) (mm) 0.025 0.64 0.050 1.27 0.075 1.9 0.10 2.54 0.125 3.18 0.150 3.81 0.175 4.45 0.20 5.08 0.3 7.62 0.4 10.16 ASTM D 1883 Standard Load (2.5 mm) = 13.2 kN CBR% (2.5 mm) CBR% (5 mm) Penetration - Load Calculations Load (kN) 1 0 6.3 10.43 13.58 16.5 18.86 20.89 23.1 Date Date Tested 24.9 28.35 Tested By Test Condition Standard Load (5 mm) = 20 kN Load (kN) 2 0 5.32 7.49 8.33 8.61 9.16 9.7 10.5 11.12 17.41 CBR%= Load from test 2.5 cm/standard load from ASTM 2.5 cm CBR % Load from test 5 cm/ standard load from ASTM 5 cm -
43. Eolian deposits tenda. Coarse grainedb. Grain no bigger than sandc. Corner detailsd. Round details
12. In a one-way slab 50% of the #8 tension epoxy coated bars are going to be spliced. At the location of the splice the ratio of area provided to area required is greater than 2. Determine the value of the splice length if the bars are spaced 6 inches on center and have a cover of 1.5 inches. Assume f'c = 4000 psi and fy = 60,000 psi.
b) A7 in – 17 Ib/ft (6.538in ID) casing string is set at 8,000 ft deep in a 8 3/4 in hole. A height of 3,850 ft of cement is required in the annulus, and 60 ft of cement is left in the casing. Caliper measurements indicate the following average diameter: Well Depth ft 7000-8000 6000-7000 5000-6000 4000-5000 Average Diameter inch 91/8 91/4 95/8 93/8 i. Calculate the volume of cement slurry required using the caliper measurements and 15% of excess, and ii. Without using the caliper measurement and 50% of excess. Calculate, for each case, the number of sacks of cement if the yield is 1.1ft³/sack.
Please show solution using ASD method