ASAP Q2: A composite material has a cross-sectional area of 1150 mm². The fibers carried a stress of200 MPa and a force of 78600 N and the total longitudinal strain is (1.56 x 10°). The matrix carried astress of 6.18 MPa.1. Find force carried by the matrix.ii. Find the modulus of elasticity in the longitudinal direction and the modulus of elasticity for thefiber and the matrix.

Given:At=1150 mm2σf=200 MPaFf=78600 Nεt=1.56*10-3σm=6.18 MPa

Q2: A composite material has a cross-sectional area of 1150 mm². The fibers carried a stress of 200 MPa and a force of 78600 N and the total longitudinal strain is (1.56 x 10³). The matrix carried a stress of 6.18 MPa. i. Find force carried by the matrix. ii. Find the modulus of elasticity in the longitudinal direction and the modulus of elasticity for the fiber and the matrix.

Q2: A composite material has a cross-sectional area of 1150 mm². The fibers carried a stress of 200 MPa and a force of 78600 N and the total longitudinal strain is (1.56 x 10³). The matrix carried a stress of 6.18 MPa. i. Find force carried by the matrix. ii. Find the modulus of elasticity in the longitudinal direction and the modulus of elasticity for the fiber and the matrix.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rank 1-4
AMNT 280 Assignments 1-4 Media Presentation Categories Of Reciprocating Engines Develop a Media Presentation develop a power point media presentation Presentation will require researching a module specific topic For this activity you will research the four categories of reciprocating engines In your presentation address the following: 1 Research the four different types of reciprocating engines2 Provide an overview of the design, construction, and firing order of each engine 3 Provide research concerning which air frame used the engine Presentation Guidelines Note:This information applies to all Media Presentation activities and will not be repeated Present your research material in the format of a written document (Introduction, body, and conclusion) Presentation requirements consist of 5-7 slides with a balance of both bullet text information and images; does not include the title or reference slide APA formatting and structural guidelines apply Additional information…
R2
Which tool helps to categorise risks into three colour-coded zones representing major, moderate, and minor risks Risk Priority Number Risk assessment matrix Failure Mode and Effects Analysis O Severity Matrix
F P F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.
18 - Which of the following judgments has been given incorrectly for glasses?A) Glass in molten or liquid state has a high viscosity.B) Glass is a hard and solid material to the touch.C) The main ingredient of glass is silicon dioxide.D) Viscosity of glass in liquid state at 1000 0C is higher than the densest oil.E) The viscosity increases gradually when the glass is heated and decreases gradually when it is cooled.
27 MENG201 Mechanical workshop practice
Based on the table and the correct answers provided in Parts A-D, Are any of the claimed efficiencies impossible?
Select one: O a. X=1,498 m O b. X 0,498 m O c. X=0,754 m O d. X 0,0498 m k = m x(t) 3EI 3EI 13 13 y(t)
! (asap)
Te-Learning Portal Courses Reports e-Services Which of the following statement is correct Select one: of O Fiction is very bad at rough surfaces ion O Friction is zero for smooth surfaces O Friction is good at smooth surfaces O Friction is high for rough surfaces
Through the following formulas: (100-FGM) DP 100-IGM WGI= where: WGI - Wet grain input in ton/h DP-Dryer performance in ton/h FGM - Final grain moisture in % IGM - Initial grain moisture in % EP =WGI-DP where: EP - Evaporation power in ton+₂0/h EC = GC HP where: EC - Energy consumption in kcal/h GC-gasoil consumption in kg/h HP-heating power of gasoil in kcal/kg SEC where: SEC - Specific energy consumption in kcal/kgH20 Select which of the following specific energy consumption options correspond to a dryer that has a performance of 40 tons/h, and is required to reduce grain moisture from 17% to 13.5%. Data: EC EP-1000 heating power of gasoil-10100 kcal/kg gasoil consumption=213 kg/h Answer 500-1000 kcal/kg H20 1500-2000 kcal/kg H20 1000-1500 kcal/kg H20 O O O