Q1. Determine the net bearing pressure for a 3m x 3m footing at a depth of 2 m in a medium dense sand so that the total settlement does not exceed 25mm. The average and corrected SPT blows below the footing (upto B) is N60 = 28 and average moist density is 1.75 t/m3 . The water table is more than 3 m below the footing

Q1. Determine the net bearing pressure for a 3m x 3m footing at a depth of 2 m in a medium dense sand so that the total settlement does not exceed 25mm. The average and corrected SPT blows below the footing (upto B) is N60 = 28 and average moist density is 1.75 t/m3 . The water table is more than 3 m below the footing

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Mat Foundations

Section: Chapter Questions

Problem 10.1P: Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The...

See similar textbooks

Similar questions

A 2m x 3m footing constructed on a sand deposit (as shown in the Figure below) is subjected to centric vertical loading at a depth of 1.5m below the ground surface. Energy-corrected SPT Noo values from the field are given below. Assume c' = 0, y = 18.5 kN/m, Vat = 19.5 kN/m, %3D Assuming Factor of Safety = 3, compare the gross allowable load for the following scenarios. (a) When the ground water table is located at the ground surface. (b) When the ground water table is located 0.5 m below the ground surface. (c) When the ground water table is located at the base of the footing. (d) When the ground water table is located 1m below the base of the footing. (e) When the ground water table is located 5 m below the base of the footing. Ground water D able Casel D Casell Yaturated unit weight Depth (m) Neo 1.5 3.0 4.5 6.0 10 7.5 10 9.0
Problem 6: A strip footing founded on dense sand (p =35° from direct shear tests and ysat-17kN/m³), is to be designed to support a vertical load of 400kN per meter length. Determine a suitable width for this footing for FS=3. The footing is located 1 m below the ground surface. The groundwater level is 10 m below the ground surface. Use Meyerhof Eq. but for shape factors to Use DeBeer and for depth factor to use those proposed by Hansen. (use Yb-15.5kN/m³)
2) A square footing carries an allowable load of 59130kg including its own weight. The bottom of footing is 1.0m below ground surface and water table coincide with bottom of footing. Assume General shear failure. Unit Weight = 1846kg/cu.m c= 1605kg/sqm Nc = 35 Nq=22 Ny=19 1.0m Sat unit wt = 1956kg/cu.m
A square footing having the dimension of 24 x24 (B=L=24) is to beconstructed on a deep clay deposit. Superstructural stress is calculated as 150 kPa. Thefoundation will rest at the depth of 2 m from the surface. The groundwater table is located onthe surface and the saturated unit weight of the clay is 17 kN/m3. Determine the depth of theborehole considering both de Beer’s rule and the Turkish Earthquake Code (2018).
A proposed office building will include a 10 ft x10 ft square, 3 ft deep (the footing height is also 3 feet) spread footing. The normally consolidated clay has the following engineering properties: Ydry = 115.0 pcf $'=24° c'=90.0 psf Cc/(1+eo) = 0.15 The soil stratum extends to a great depth, and the ground water table is 50 ft below the ground surface. Using the classical piece-wise log-linear method, estimate the total settlement of this footing considering only the allowable bearing pressures using ASD approach. The unit weight of concrete is 150 pcf. State any assumptions made.
2. A 2m X 2m footing carrying 1400KN load is constructed in a site with 2.5m thick clay layer under a 2.5m thick sand layer. If the footing and the ground water table are located at 1.5m below the surface, calculate the consolidation settlement of the footing. You may assume the following soil properties: for sand sat 15.7kN/m°, and for clay eo= 0.65, Cc = 0.25, Cs = 0.06, O'p = 200kN/m² and sat =19.25KN/m³. 19.25kN/m and t = %3D
A rectangular footing 3m by 4m is founded 1.2m below the ground surface for which the unit weight of soil is 17.8kN/m3. The cohesion strength is 10kPa and the angle of internal friction is 20degrees. Under the condition of general failure, evaluate the contribution from the following to the ultimate soil bearing capacity in kPa. The ground water table is at a level that does not affect the unit weight of the soil. Use Terzaghi’s bearing capacity factor. For Ø=20degrees: Nc = 17.69, Nq = 7.44, Ny = 3.64. 23. Due to Cohesion Strength Due to soil overburden Due to footing dimension
3) A circular footing having a diameter of 1.2m has its bottom at a depth of 2.7m from the ground surface. Water table is located at a depth of 1.3m below the ground. Soil has the ff. properties. Dry unit weight = 18.1kn/cum Saturated unit weight = 19.3kn//cum C = 15.74kpa Angle of internal friction = 20deg %3D a) Assuming local shear failure, find ultimate bearing pressure using terzaghi's equation b) Det. Allowable bearing capacity using a factor of safety of 3. c) Find allowable load on footing.
1. A 3m x 3m square footing is constructed at a depth of 2m in a 26m deep clay layer with following soil properties: ] =16.5kN/m³, Normally Consolidated Clay, e̟= 0.65, Cc = 0.25,s=0.5 and Es= 6.0 MN/m2. If there is a 1000kN structural load on the footing, calculate the consolidation settlement of the footing.
8. A loaded footing ABCD with q = 200 kN/m² on the ground is shown in the figure below. Compute Aoz under Points E, F, B, and G at a depth of 5 m 3 m 2 m D H q = 200 kN/m² IĘ %3! 2 m A F G
Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The distance between the two column loads L3 = 13.5 ft. The proximity of the property line at the left edge requires that L2 = 3.0 ft. The net allowable soil pressure is 2500 lb/ft2. Determine the breadth and length of a rectangular combined footing.
A 2.0 m 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c = 0, =26, = 19 kN/m3, cu = 60 kN/m2 (=0 condition). Determine the maximum possible value for Q, considering short-term and long-term stability of the footing.