Q1. A single phase A.C. radial distributor system has long of 600m and a total impedance of (0.05+j0.05) 2 and is fed from one end. The system is loaded as follows: (1) 85 A, 0.6 power factor lagging, 200m from feeding point A. (2) 100 A, 0.8 power factor lagging, 400m from feeding point A. (3) 50 A, unity power factor lagging, at the far end. If the voltage Vc-250230 Calculate: 1- The voltage at feeding point of the feeder. 2- The voltage at the far end of the feeder.

Q1. A single phase A.C. radial distributor system has long of 600m and a total impedance of (0.05+j0.05) 2 and is fed from one end. The system is loaded as follows: (1) 85 A, 0.6 power factor lagging, 200m from feeding point A. (2) 100 A, 0.8 power factor lagging, 400m from feeding point A. (3) 50 A, unity power factor lagging, at the far end. If the voltage Vc-250230 Calculate: 1- The voltage at feeding point of the feeder. 2- The voltage at the far end of the feeder.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
The reactance of a generator is given as 0.1 pu based on the generator of 17 KV, 300 MVA. Determine the pu reactance on a base of 17 KV, 250 MVA. New pu reactance is.......
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
QUESTION 1 Two magnetically-connected circuits have the following characteristics: . A series-opposing connection of coils (dot convention). The primary side is connected to a voltage source that has a magnitude of 230 V and a phase angle of 45 degrees. . The primary-side inductive reactance is jXL1 - j8 Ohm. . The secondary side is connected to a resistive load of 10 Ohm. . The secondary side inductive reactance is jXL1 =j5 Ohm. . The mutual inductive reactance is jM=j1 Ohm. The magnitude of the voltage across the resistive load is:
Q20. The section bus-bars A and B as shown in Figure B5 are linked by a bus-bar reactors each rated at 5000 kVA with 10% reactance. On bus-bar A, there are two generators each of 10,000 kVA with 10% reactance and on B two generators each of 8000 kVA with 12 % reactance. Find the Current and MVA that fed into a dead short circuit between all phases on B with bus-bar reactor in the circuit. Page 4 of 5 جامعة التقنية والعلومر التطبيقية بإبراء University of Technology and Applied Sciences - Ibra Student ID: Section: Student Name: 8,000 kVA 12% 10,000 kVA 10,000 kVA 10% 8,000 kVA 12% 10% 2 3 5,000 kVA 10% lell 8,000 kVA 10% Figure B5 "End of Question Paper"
The section bus-bars A and B are linked by a bus-bar reactor rated at 6000 kVA with 12% reactance. On bus-bar-A, there are two generators each of 10 MVA with 8% reactance and on bus-bar-B, two generators each of 6000 kVA with 10% reactance. Find the steady MVA fed into a dead short circuit all phases on B with bus-bar reactor in the circuit.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
A single phase 120V AC sourc controls power to a resistve load 20N using integral cycle control. a) Find the output power for both output voltage waveforms shown below. b) The voltage and the current ratings of the switch. c) The duty cycle and the value of TON to produce 0.63KW power. d) The power factor for part (c). Awww TON -TON
For a power station the yearly load duration curve is a straight line from 50,000 to 4000 kw. To meet the load three turbogenerators are installed. The capacity of two generators is 20,000 kw each and the 3rd is rated at 7,000 kw. a. Draw the annual load duration curve b. Determine the following the Energy generated per year, Load factor and Annual Capacity factor.