5:08Class Work March 1...Class Work March 11, 2021Fluid MechanicsQ1The machine C shown in Fig. (3) Is it turbine or pump? What is the water power(kilowatt) associated with this machine? If the flow discharge is 200 Ips, PA =206 kN/m2, PB = 690 kN/m?, elevation of A = 67 m and elevation of B = 30 m.Neglect losses.D-300 mmD- 200 mmFig. (3)Q2Gate AB in Fig. (2) is 1.5 I Wide mo tne paper, ngcu at A, and restrained by

Answered: Image /qna-images/answer/dd4a314a-4ad2-4026-a08c-728fa78d8793.jpg

Q1 The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated with this machine? If the flow discharge is 200 lps, PA= 206 kN/m², PB = 690 kN/m², elevation of A = 67 m and elevation of B = 30 m. Neglect losses. D- 300 mm D-200 mm Fig. (3)

Q1 The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated with this machine? If the flow discharge is 200 lps, PA= 206 kN/m², PB = 690 kN/m², elevation of A = 67 m and elevation of B = 30 m. Neglect losses. D- 300 mm D-200 mm Fig. (3)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q7/ Lake A losses feed Lake B. The distance between them is 3.5 km. Lake A has a water level of…

Q: QUESTIONS: 1) ZB в A Zp V D Figure 1 The physical characteristics of the pipes are seen in the Table…

A: Apply energy between AC and BC and between AD and BD

Q: Ex. Drive the Bernoulli eg. For the fig. show the discharge flow 0.5m3/sec and find h density of…

A: Given data - pw = 1000 kg/m3 phg= 13600 kg/m3 Q = 0.5 m3/s Find out - Value of h ?

Q: nooth hump produses a drop of 15 cm in the water sur sses and calculate the discharge per unit width…

Q: An orifice of 0.1-meter-diameter is installed in a pipe having a diameter equal to 0.3 meters as…

Q: Water is pumped from the river through a 45-mm-diameter hose having a length of 3 m. The friction…

A: Diameter of the pump hose = 45mm = 0.045mLength = 3mFriction…

Q: Q3) the difference in water surface between two reservoirs is 8m, these reservoirs are connected by…

Q: 42. The flow in line AD 0.219 m³/s 0.203 m³/s 0.234 m³/s 0.126 m³/s 43. The flow in line DC 0.186…

Q: (c) Figure Q4(c)(i) shows the system consists of 1200 m of 5 cm cast-iron pipe, two 45° and four 90°…

A: L = 1200 mD = 5 cm or 0.05 m Q = 0.005 m3/s = 0.001 kg/m s

Q: Water at T = 25°C is drawn from an underground detention tank and discharged into a drain using a…

A: Temperature is,To determine:Part A): Available NPSHPart B): Required NPSH

Q: View Policies Current Attempt in Progress The turbine shown in the figure below develops 100 hp when…

A: Determine (a) the elevation h, (b) the pressure difference across the turbine, (c) the flowrate…

Q: Given: Q=10.2 lit/sec Length of A=120m Length of B=2180m f of A=0.0138 and of B f=0.0142 pump…

A: We know that Power formula for pumping considering effciency of pump is given by P = P= powerP =…

Q: A centrifugal pump discharging 900 gpm and operates at 1800 rpm against a head of 120 feet has a…

Q: For the flow net shown below, the soil is isotropic having a permeability of 0.002 cm/sec. Determine…

Q: PROBLEM 3 An 85-percent-efficlent pump is used to Increase the pressure of water in a 10-cm-diameter…

A: To find out the A) Head Added by pump. B) Required horse power of the pump for discharges 0.015…

Q: Pipes 1, 2, and 3 are parallel with each other as shown.If the energy at the inflow pipe A is 147…

Q: 6. Flow nets a) Calculate the flow through earth dam shown in the following figure. (scale drawing…

A: the given soil permeability, K =6.5·10-5 m2s·m2Head at dam, H=5m

Q: A pump is used to lift 120 L/s of water at 10°C from a river to a storage tank that has a free…

A: Given, Q = 120 L/s or 0.12 m3/s D = 350 mm or 0.35 m L = 1200 m e = 0.02 mm

Q: 3: Answer either A- A submerged pipe outlet has the following data: F.S.L of distributary 100.00 m,…

A: As there are two different questions and nothing is mentioned which one to solve, So as per…

Q: Consider the section of water distribution piping shown below. This figure is not to scale. Ignoring…

A: Given- It is required to find- The values of - Total flow into the system (Qdemand). Total…

Q: Two reservoirs are connected by distribution pipeline as shown in the figure. Assuming no head loss…

Q: Pipes 1, 2, and 3 are parallel with each other as shown.If the energy at the inflow pipe A is 133…

A: Pipe 1 Diameter = 552 mm, Length = 159 m and C = 104 Pipe 2 Diameter = 676 mm, Length = 211 m and C…

Q: Consider the section of water distribution piping shown below. This figure is not to scale. Ignoring…

A: Given data- A section of water distribution piping- Minor losses are ignored. To Find- The values…

Q: 2) Water is pumped from a lake to a storage tank h=30 m above at a rate of 500m³/s, with a pump of…

Q: Reservoir A and B located at 220 m and 100 m elevation respectively is connected by a 300mm diameter…

Q: 3. Is the pump likely to cavitate? Support answer with a NPSH calculation approach.

A: Given-a pumping system consisting of a suction pipe and delivery pipe since the question has…

Q: Q2 Water flows from reservoirs A and B to point C (discharge to atmosphere) through pipes 1 and 2 as…

Q: H-W1 Q1/ Neglecting losses, determine the discharge in Fig. below Oi so 075 Q2/When the pump in Fig.…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: Determine the flow in each pipe in the reservoir shown below. Use the values provided in the table.…

A: To Determine the flow in each pipe in the reservoir shown.

Q: 2. The total discharge from A to B in figure is 12 l/s. Determine the discharge pipes 1 and 2 if the…

A: Given Data : Total discharge from A to B = 12 l/s f = 0.035 Determine the discharge in pipe 1 and…

Q: A pump is used to raised water to a reservoir through 1000 m. long of 20 cm diameter with Cw of…

A: Introduction : To depict the variation of the piezometric head, a hydraulic grade line (HGL) can be…

Q: View Policies Current Attempt in Progress Water is pumped from the large tank shown in the figure…

Q: 200 GYA DETERMI NE ROTANON つy 72KN ○の米

Q: Your assigned problem: With a total flow of 14 cfs, determine the division of flow and the head loss…

A: In this question of pipe network is given which is in parallel flow and we are asked to find out the…

Q: According to Figure 1, information given de= 500mm, Ve= 7.0 m/s, h= 5.0 m and Pe= 105 kPa.…

Q: Water is at 20°C is pumped from a lower reservoir to a higher reservoir by a pump at a rate of 10…

A: To Determine the friction head loss (m)?

Question

5:08
Class Work March 1...
Class Work March 11, 2021
Fluid Mechanics
Q1
The machine C shown in Fig. (3) Is it turbine or pump? What is the water power
(kilowatt) associated with this machine? If the flow discharge is 200 Ips, PA =
206 kN/m2, PB = 690 kN/m?, elevation of A = 67 m and elevation of B = 30 m.
Neglect losses.
D-300 mm
D- 200 mm
Fig. (3)
Q2
Gate AB in Fig. (2) is 1.5 I Wide mo tne paper, ngcu at A, and restrained by

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Complete solution pls
All values should not be rounded off until the final answer.
pls do not round off the decimal. only in the final answer
i need the answer quickly
Water is flowing in a 3 m wide rectangular channel. A hydraulic jump occurs and the flow upstream is 360 mm deep while the flow downstream from the jump is 1300 mm deep. A) Find the discharge flowing in the channel. B) Find the energy absorbed by the jump in kW. Please answer correctly
For the setup shown in the figure :
Please solve in detail.
answer fast
Be fast and quick and correct.
Q4: The pump shown in figure (2) adds 25 kW to the water and causes a flow rate of 0.04 m³/s. Determine the flow rate expected if the pump is removed from the system. Assume f= 0.016 for both case and neglect minor losses. 40-mm-diameter nozzle (2) 60-mm-diameter, 30-m-long pipe; f = 0.016 Pump T h (1) Fig. (2)
Q.solve itt.