Q1) In the transformer-coupled filter-bridge circuit shown, the va the transformer secondary voltage rating (Vsec), capacitor (c frequency (f) are given on Table.1 on the last page. Answer the fo questions assuming practical diode models: Rurge Vout 120 V rms 100 R 3.3 kn a) Determine the ripple factor b) Determine the diode peak inverse voltage and explain its impo in the rectifier circuit? c) Draw the following voltage waveforms in relationship to th waveforms (show two full cycles): Vp. Vic. and V.

Q1) In the transformer-coupled filter-bridge circuit shown, the va the transformer secondary voltage rating (Vsec), capacitor (c frequency (f) are given on Table.1 on the last page. Answer the fo questions assuming practical diode models: Rurge Vout 120 V rms 100 R 3.3 kn a) Determine the ripple factor b) Determine the diode peak inverse voltage and explain its impo in the rectifier circuit? c) Draw the following voltage waveforms in relationship to th waveforms (show two full cycles): Vp. Vic. and V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the circuit diagram of a single phase full-wave uncontrolledrectifier with R-load. Describe its principle of operation. Draw thewaveforms of: input voltage, voltage across the load, current throughthe diodes and their voltage. Write the expressions for: the averageoutput voltage Vd, the maximum reverse voltage across the diode and thestandard transformer power. Describe what the difference will be if acapacitor is added in parallel with the load at the output.
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
Show the downward shift of the output signal with the series capacitor and diode. Clampers or DC restorers are clamp a peak of a waveform to a specific DC level compared with a capacitively coupled signal which swings about its average DC level (usually 0V). If the diode is removed from the clamper, it defaults to a simple coupling capacitor– no clamping. What is the clamp voltage? And, which peak gets clamped? Why is this so? Produce a schematic diagram with LTspice schematic capture program. Voltage values: Capasitor value: 1000 pF DC offset: 0 V Amplitude: 5 V Freq: 1 KHz
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
Draw circuit diagram with the help of diodes. The current vs voltage graph at the output of the circuit is shown below ...
For the circuit shown in Figure, consider Ideal diodes. If Vs = 19sin wt, Vb = 4 V, the minimum value of output voltage is: Vout at of estion Vs Vb Oa. -4 V Ob. -15 V Oc. -19 V Od. 4 V
1) the transformer turn-ratio (N1/N2) =? / 2) the PIV rating of diode =? /3) average power dissipated in diode PD =? / 4) the value of filtering capacitor (C) required to give ripple voltage Vr=0.5v is ? / 5) if each diode has rf=15 ohm and for same vm =12v, the peak secondary voltage Vsp=? / 6) if D1 is open then the average output voltage Vo(avg)=?
Assume the diodes to be ideal ,descibe the transfer functionality for the following circuit.
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). (b) Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
In the circuit given in the figure, since Vi is a square wave with a frequency of 1 kHz and an amplitude varying between +5V and -5V; Vi and Vo voltages one after the other and in scale; a) Draw with Zener diode is not active ? b) Draw with the Zener diode on? (Assume the diodes in the circuit are ideal)
Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage VPP=20 V and bias voltage VBias= 2.7 v. a) What is the function of the circuit? b) Draw the circuit diagram. c) Draw the input and output waveforms.