For the given circuit: if Vin = 200 V rms, R, = 2.2 k2, f = 60 Hz, answer the following questions (assume practical diodes). a) Calculate the peak output voltage, Vp(rect) b) What is the peak forward current I, through each diode and the average power P(avg) that is delivered to R c) If a capacitor filter is connected from the rectifier output to ground, and the peak to peak ripple voltage was found to be Vr(pp) = 0.8 V, determine the value of the capacitor. d) Draw the output voltage waveform for the unfiltered rectifier and for the filtered rectifier in relationship to the input waveform (show two full cycles). Show all the necessary values on the graphs. 4:1 DI Vin RL D2 elle lell

For the given circuit: if Vin = 200 V rms, R, = 2.2 k2, f = 60 Hz, answer the following questions (assume practical diodes). a) Calculate the peak output voltage, Vp(rect) b) What is the peak forward current I, through each diode and the average power P(avg) that is delivered to R c) If a capacitor filter is connected from the rectifier output to ground, and the peak to peak ripple voltage was found to be Vr(pp) = 0.8 V, determine the value of the capacitor. d) Draw the output voltage waveform for the unfiltered rectifier and for the filtered rectifier in relationship to the input waveform (show two full cycles). Show all the necessary values on the graphs. 4:1 DI Vin RL D2 elle lell

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage V=20 V and bias voltage V 2.7 v. a) What is the function of the circuit b) Draw the circuit diagram. c) Draw the input and output waveforms. Input Output
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consisting series connected a resistor and an inductance from a 70.7V (RMS), 50HZ sinusoidal AC source. The firing delay of the thyristor is 90° and the load values are R=10Q, L=0.1 H. Define the load current expression and draw the load current by calculating for first two periods. And calculate the average values of the load voltage and current.
.Draw a full-wave rectifier circuit (using a diode bridge) and predict the output voltage signal when the input is a sinusoidal signal with amplitude 10 V (p p). Use the previous full wave rectifier to create a peak detector with a 2 V ripple.
In a full wave rectifier circuit involving double diodes, a sinusoidal input signal of the following nature is applied e=10 sin(500*pi*t) V. What will be value of the dc voltage obtained at the output of the rectifier.
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
29. Does an increase in reverse bias for a Varactor diode cause an increase or decrease in capacitance? 30. If the load current through a SCR (Thyristor) reduces to almost zero, what will be the result?
Given the half-wave rectifier circuit shown 220V 60Hz 220V:Es Es D RL The load resistor is 2292 and it dissipates 2W. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average diode current and PIV of the diode.
Two identical Schottky diodes are connected in series, one in the forward and the other in reverse direction, see figure. Assume the reverse saturation current, IS, of each diode to be known. Derive he current-voltage curve I(V) of this circuit. Plot it with the ratio I / IS on the y-axis and V / Vth on the x-axis. Make sure to cover a broad range of voltages, say, from –10 Vth to 10 Vth.
Q1 A. Design a clamper to perform Silicon diodes 10 V 2.7 V the function indicated in Figure shown below. Design B. Clip the output waveform to -10 V -17.3 V (+0.7 V and -0.7 V).