Q1: In the [MLT] system, what is the dimensional representation of (a) enthalpy,(b) mass rate of flow.Answer: (a) [L/T2]; (b) [M/T]

Answered: Q1: In the [MLT] system, what is the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An elastic foundation is often used to support heavy machinery that vibrates in such a way to cause problems for the rest of the structure. An elastic foundation with two equal springs each of stiffness k = 600 lbs/in is used to support the equipment of weight W = 1000 lbs shown. The equipment vibrates in such a way that it causes a vertical forcing function P(t) = 100 sin(20t) [lbs]. %3D (a) Draw the degree of freedom for the motion of the machinery. (b) Determine the equation of motion. What type of motion is this? (c) Determine the natural frequency and the displacement of the machinery. (d) What is the maximum amount of force that will be felt by the rest of the structure? (Think about what causes force to the rest of the structure) Rest of structure Hww
Complete the following table for saturated water. Temp T ("C) Pressure P Entropy s (kJ/kg.K) Quality x Phase description (kPa) 120 5000 [1.1]? [1.2]? [1.3]? 50 1000 [1.4]? [1.5]? [1.6]? 400 1800 [1.7]? [1.8]? [1.9]? [1.10]? 40 [1.11]? X = 0.9 [1.12]?
This is for my thermodynamics chorus! Please consider degrees of freedom, the universal gas constant and the individual gas constant. Do not use PV=nRT for (c) Use another form of the ideal gas law to solve
answer b
physical quantities m, r, u, a, and t with dimensions [m] = M, [r]= L, [v] = LT, [a] = LT-2, and [t] = T. Enter the dimensional expression of the quantity on the right-hand side of each equation. Your answers may contain only M, L, T, and exponents. Assume that each of the following equations is dimensionally consistent. F = ma [F] =
Fill in blank hell
The Antoine Equation can be used to estimate vapor pressure at various temperatures for different substances using sets of empirically-derived constants. The equation can be written as: Where for water A = 8.07131, B = 1730.63, C = 233.426, T = temperature [°C], and P = vapor pressure [mmHg]. Note that with these constants the temperature and pressure must be provided in °C and mmHg, respectively. Using the Antoine Equation and the provided constants, what atmospheric pressure (provided in terms of % of standard atmospheric pressure) will permit water to boil at 75 °C?
2. Complete the blank cells in the following table of properties of steam. In the last column describe the condition of steam as compressed liquid, saturated mixture, superheated vapor, or insufficient information; and, if applicable, give the quality. P[kPa] T[°C] v[m³/kg] а. 500 20 b. 500 0.20 с. 1400 200 d. 300 0.8
A heat generating slab with thermal conductivity of k [W/m-K] and heat generation rate d" [W/m³] is perfectly insulated on the left side (x = 0) . h1 and is exposed to air with ambient temperature T1 [K] and convection coefficient of hi [W/m²-K] on the right as shown in Fig. 1. Neglect Air Slab radiation. Find out the temperature distribution (i.e., temperature as X= () a function of x) within the slab in terms of the variables shown in the Figure 1: Note the figure. indicated positive direction for reference. SPerfect Insulation
Hi! I did not calculate the table, can you help me please ? Course name is Heat Transfer. Thank you!
To understand the heat transfer from a bar in cross flow, you conduct a series of experiments measuring the average heat transfer coefficient as a function of the free stream velocity. A schematic of the experiment and the accompanying results are shown below. L = 0.3 m h [W/m²-K] 60 40 V [m/s] 20 15 a) You expect the important dimensionless parameters to be related by a function of the form Nu = CRe Pr where C, m, and n are constants. The film temperature in both the experiments is approximately the same. Use the given experimental results to determine the constant m b) Calculate h for L = 0.75 m and V = 30 m/s.
==== 25°C and A closed rigid tank contains 0.5 kg of Refrigerant 22, initially at a temperature T₁ pressure p₁ = 6.0 bar. The tank is cooled until the temperature is T₂ = -10°C. Assume changes in kinetic and potential energy are negligible. Determine: a. final pressure [bar] Handwritten,no gpt b. heat transfer [kJ] during the process (indicate magnitude and direction)

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Q1: In the [MLT] system, what is the dimensional representation of (a) enthalpy, (b) mass rate of flow. Answer: (a) [L/T2]; (b) [M/T]