Three cables AB, AC, and AD are used to hang a traffic light as shown. All three cables have diameter d = 3 mm and are made out of 2024-T4 aluminum. If the failure criterion of the overall system is a safety factor SF, = 8 against yielding, what is the maximum traffic light weight that can be hung? Take 0 = = 35°, L= 5, and h = 12. W max 663.84 B L A 10 D N 2. x 0%

Three cables AB, AC, and AD are used to hang a traffic light as shown. All three cables have diameter d = 3 mm and are made out of 2024-T4 aluminum. If the failure criterion of the overall system is a safety factor SF, = 8 against yielding, what is the maximum traffic light weight that can be hung? Take 0 = = 35°, L= 5, and h = 12. W max 663.84 B L A 10 D N 2. x 0%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Select the lightest WT4 shape to be used as a 20 ft long tension member to resist the of dead load, D=40 k, live load, L=60 k, snow load, PS=25 k, and earthquake, E=110 k. The connection is two lines of bolts through the flange with three 3/4-in ∅ bolts in each line spaced at 3 in on center. Use A992 Grade 50 steel. Neglect block shear.
Part A The strut is supported by a pin at C and an A-36 stoel guy wire AB. (Eigure 1) If the wire has a diameter of 4.8 mm, determine how much t stretches when the distributed load acts on the strut. Express your answer three to significant figures and include the appropriate unita. ? SAn = Value mm Figure 3AANm 27 m
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
Select the lightest WT4 shape to be used as a 20 ft long tension member to resist the following service loads: dead load, D = 20 k, live load, L = 35 k, snow load, S = 25 k, and earthquake, E = 50 k. The connection is two lines of bolts through the flange with three 3/4-in Ø bolts in each line spaced at 3 in on center. Use A992 Grade 50 steel. Neglect block shear.
A 400 ft long elevator cable (diameter of 1 inch) is made of 4130 steel with a yield strength of 120 ksi. How much weight can the cable hold with a factor of safety of 5.2? Wwinen
Calculate the safety of the cylinder pivot pin in relation to the yield. The tensile yield strength of the pin material is ReL=600MPa. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mmy2 = 798 mm Piston rod = φ32mm Cylinder pivot pin = φ25mm Pliers pivot pin = φ30mm The clamping force of the pliers is 6000N Answer to one decimal place !!
For the lap connection shown, the rivets are 19-mm diameter and the plates are 8 mm thick. The rivets used are A502, Grade 1 and the plates are ASTM A36 with Fu = 400 MPa. Determine the value of Pin all possible modes of failure and the safe value of P that the connection can resist. Fv = 120 MPa, Fp = 1.2 Fu. Add 1.6 mm for the hole diameter. Ans. 297.6 KN
8. A concrete wall footing with a width of 0.9 m and a depth of 0.6 m supports a centrally placed 0.6-m-thick wall. The ultimate bearing stress for the soil under the footing is 47 kN/m2. What is the height of the wall if a factor of safety of 5.0 is used? Concrete weighs 23.5 kN/m3 (assume depth of one meter) NOTE: please check options 0.6m R(m) Jestion 0.6m tely ar ate 05.16 m oogle pject) O 14.4 m MG-40 16 O5 pm ourse 1.8 m
The following data is given for th4e bracket illustrated below. P=25 kN, e = 100 mm, 11 = 150 mm, 12 = 25 mm. There is no pre-load in the bolts. The bolts are made of plain carbon steel 45C8 (oy = 380 N/mm²) and the factor of safety is 2.5. Using the maximum shear stress theory, specify the size of the bolts. cessibility: Investigate 11€
The aircraft link is made from an A992 steel rod. (Figure 1) Figure < 1 of 1 18 in.
• Bars (1) have a cross-sectional area of A₁ = 0.65 in.2 and a length, L₁= 7 ft. • Bars (1) are made of cast iron with an elastic modulus of E₁ = 24,000 ksi, a coefficient of thermal expansion, a₁ = 12.3 x 10-6/°F and yield strength of oy = 120 ksi. • Bar (2) has a cross-sectional area of A₂ = 1.45 in.² and a length, L₂ = 5.5 ft. • Bar (2) is made of stainless steel with a coefficient of thermal expansion, a₂ = 10.6 × 10-6/°F. • The stress-strain diagram provided below presents the results of the stainless steel's (i.e., Bar (2)) bar tension test. • There is a gap of A = 0.1 in. in the connection at B and a = 3 ft. • All bars are unstressed before a load P = 12 kips is applied and the temperature increases by AT = 40°F. Stress-strain diagram for stainless steel bar: (1) a Stress (ksi) L2 Rigid bar 120 100 80 60 40 20 0 0 0 B (2) P a (1) C Upper scale L₁ Connection details at node C Lower scale. C 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.006 0.008 0.010 0.012 0.014 0.002 0.004 Strain…
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures