Q1: A sag vertical curve connects a (-3.5%) grade and a (+0.5%) grade. The PVC is at station (3+70.00) at an elevation of 321m. The length of the curve = 200m. Choose the correct answer for the following: 1. The station of the PVI: (A) 4 + 80 (B) 4+70 (C) 3 + 80 (D) 3+17 (E) None of them

Q1: A sag vertical curve connects a (-3.5%) grade and a (+0.5%) grade. The PVC is at station (3+70.00) at an elevation of 321m. The length of the curve = 200m. Choose the correct answer for the following: 1. The station of the PVI: (A) 4 + 80 (B) 4+70 (C) 3 + 80 (D) 3+17 (E) None of them

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2. (10 pts) Refer to Figure 1. Due to application of line load q₁, the vertical stress increase at…

Q: d. The maximum moment under the 50 KN load e. The maximum moment under the 150 KN load - f. The…

Q: ISA 90*60*8 mm of steel of grade fe-410 is connected to a 12mm gusset plane ans is used a tension…

A: Welded connections are provided in steel structures since it is lighter, quicker, adapting and gives…

Q: 8. Resultant force on a 1 mx 1 m gate immersed vertically at a depth of 2 m below the free water…

A: Given data : The value of density of water ρ=1000 kg/m3 The value of acceleration due to gravity…

Q: Bernoulli's

A: Essentially a pump adds energy to a system and a turbine takes it away. Therefore typically in the…

Q: Q3: Determine 100-year flood from the flood observation in the table. Year 2010 2011 2012 2013 2014…

A: Given Data:year20102011201220132014Q,m3/sec1830477155201546201628201715201820199620205

Q: Q2: In preparing the mass haul diagram for a highway section, the following data has been obtained:…

A: Given Data: Free haul volume=800 m3 Waste and borrow=0 m3 Station points and Volume data are…

Q: You have a pipe with an inside diameter of 3.48 in. and roughness 0.00032 in. A fluid with specific…

A: step 1-

Q: 5) Select the lightest W310 that can resist the given loads as shown in the figure. Use the table…

Q: Material Strengths: Fy = 248 MPa, Fu= 400 MPa The channel (C200X17.1) is connected with four M16…

Q: tión 3: Use method of section: Find the force in member BH? * 9 kN 12 KN 9KN B lo G 130 E 10m 10m…

Q: MECHANICS Find the height to be raised of box 8 man 30kg to gain potential energy of 3000.J

A: Given data : The value of mass of box m=30 kg The value of potential energy P.E=3000 J The value of…

Q: A 200 g/l solution of common salt was discharged into a stream at a constant rate of 25.. 1/s. The…

Q: Practice Problem: Refer to Figure 3.70, a flexible square area is subjected to a uniformly…

A: Given: The distributed load (q) is 100 kN/m2. The depth is 4 m. Consider the figure,

Q: Water is flowing in a fire hose with a velocity of 1.0 m/s and a pressure of 200000 Pa. At the…

Q: 8. Resultant force on a 1 mx 1 m gate immersed vertically at a depth of 2 m below the free water…

A: Answer for given problem may have typing/printing error. For exact answer , see the solution…

Q: Estimate the capillary soil suction using the Green-Ampt equation if it takes 3.5 hours for an…

A: Given, t = 3.5 hrs L = 40 cm or 0.4 m η = 0.20 i = 2.5 cm/hr

Q: H.W3 Determine the slope and deflection of end A of the cantilevered beam. E= 200 GPa and…

A: Given data E= 200 GPa I = 65.0 x 106 mm4 here, a dummy concentrated load is applied in the…

Q: Question 2: Block A has a weight of 60lb and Block B has a weight of 10lb. Determine the speed of…

Q: 8. Resultant force on a 1 mx 1 m gate immersed vertically at a depth of 2 m below the free water…

Q: k) j) Solve for x (x-coordinate of the composite area's Centroid) Solve for y(y-coordinate of the…

A: X-Coordinate of centroid: As the composite area is symmetric about line x = 400 mm, the x-coordinate…

Q: (a) What is the effect of rising or falling stage upon the discharge-curve? (b) The following data…

Q: Q2/ The hydraulic jump occurred in an open rectangular channel with a length of 3.5 m. Assume Froud…

A: As per bartleby guidelines experts are allowed to solve only first three subparts. Please post…

Q: Determine static indeterminacy of frame

A: External static indeterminacy Dse is calculated as ; Dse = R - 3 R = reactions = 2 + 2 = 4 Dse = 4 -…

Q: What is/are the advantages of knowing how to estimate the additional stress/es due to…

A: The vertical stress increment in the subsoil decreases with increasing depth and distance from the…

Q: The staff gauge readings and the corresponding discharges measured in a stream are give below.…

A: Discharge at gauge reading 1.6 m and 2.5 m

Q: The dilution method with the sudden-injection procedure was used to measure the dis-... charge of a…

Q: 298.5 kN 3.2m 3.2m 3.2m 3.2m 3.2m T P L H ôm Å S 0 Y G B 4m R N J F em с M 1 E D

A: Solution: Given: a) Point of contraflexure occurs at the middle points of the points of the various…

Q: Q2: For the soil profile and a) Final consolidation settlement. b) Time required for the settlement…

Q: A uniform 10-kg bar OA is suspended from the pin at O. The bar is at rest when the 1.5 kg bal B with…

Q: bi ELABORATE Try solving the following problem: Practice Problem: Refer to Figure 3.8. Determine the…

Q: With regard to rock properties, define what is mass property and material property ?

Q: Symmetrical T-beam with a span of 6m The clear distance to adjacent beams is 3m. Web width = 250mm…

Q: An Evergreen's rectangular barge with 6750 m² horizontal cross- sectional area at the water line has…

Q: Q3: Indicate why Climbing lane is suggested to be used in highway works:

A: Context: Climbing lane

Q: shown? 900N/m A किन 2m Im 3m 3 Ans/S=2940 N.M²³ EI

A: As there are two different questions posted, according to the guidelines, only the first is being…

Q: o 2 significant

Q: 8 The following data are obtained from the current meter gauging of a stream, at a gauging sta-…

Q: For the beam shown in figure, find the deflection and rotation at Free end by using double…

Q: A truck and a trailer combination whose axle loads are indicated as shown is to cross a 14-meter…

Q: Rod AB consists of two cylindrical portions AC and BC, each with a cross-sectional area of 1950 mm².…

A: Deflection is the amount that a portion of a structural element moves under a load in structural…

Q: You have a pipe with an inside diameter of 3.48 in. and roughness 0.00032 in. A fluid with specific…

Q: Given ten (10) units of isolated rectangular footing, 1.20m x 2.00m x 0.30m, reinforced with 10pcs…

A: Rates are taken from CPWD DSR

Q: Please write a code in MATLAB by using the BISECTION METHOD to solve the problem below. Thank you!

A: MATLAB is to solve the problem conveniently: First we find acceptable roots of the second equation…

Q: Q1: A sag vertical curve connects a (-3.5%) grade and a (+0.5%) grade. The PVC is at station…

Q: Block A has a weight of 60lb and Block B has a weight of 10lb. Determine the speed of Block A after…

Q: spiral column is to carry a dead load 800 kN and a live load of 1350 kN. If 2% of the main bars is…

Q: Instructions: Solve the following problems as instructed. Boxed final answers and round off to the…

Q: A grade 60 reinforcing bar has a yield strength of 60 ksi. O True O False

A: Answer :- True All individual re-bar yield strengths were much greater than the mandated minimum…

Q: Fill in the blanks Smaller angle: Larger angle: s = 20 ft Determine the two possible angles so that…

A: Determine the two possible angles so that the water strikes at B.?

Concept explainers

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.

Question

Q1: A sag vertical curve connects a (-3.5%) grade and a (+0.5%) grade. The PVC is at station
(3+70.00) at an elevation of 321m. The length of the curve = 200m. Choose the correct answer
for the following:
1. The station of the PVI:
(A) 4 + 80
(B) 4+ 70
(C) 3+ 80
(D) 3+17
(E) None of them

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2. A vertical curve is to be constructed joining two gradients AB and BC. Using the values given in Table Q2, design the curve at 20 metres intervals. First Grade (± %) Second Grade (± %) 3.6 -2.2 Chainage B 2309.466 Reduced Level B 38.689 Table Q2 (Units are in metres) K-value 50
(ii) Determine the transition length based on permissible speed for a 2º curve with maximum permissible speed of 100 kmph on a BG railway track. [Consider, G = 1.676 m]
A vertical parabolic happy curve located in Malabon underpass has a grade of -4% followed by a grade of 2% intersecting at Sta. 12+150.60 at elevation of 124.80 m above sea level. The change of grade of the sag curve is restricted to 0.6%. b. Compute the elev. of the lowest point of the curve.
Given the length of vertical curve is 800 meters, the station of PVT is 225+16.0m and the elevation of PVI at the intersection of the two tangents is 620.00m, if G1 = - 2.0% and G2 = -1.2%, determine: a) The elevation of station 200 + 9.5 b) The station and elevation of the highest and lowest points on the vertical curve Note: Use 20-meter stations
A symmetrical parabolic curve has a descending grade of -0.80% which meets ascending rate of +0.4% at station 10+020 having an elevation of 240.62m. The maximum allowable change in grade per 20m station is 0.15%. Determine the stationing of the lowest point of the curve. (Answer: 10+046.67) Determine the elevation of the lowest point of the curve. (Answer: 240.83)
SITUATION 6 A -3% grade meets a +5% grade near an underpass. In order to maintain the minimum clearance allowed under the bridge and at the same time introduce a vertical transition curve in the grade line, it is necessary to use a curve that lies 200m on one side of the vertex of the straight grade and 100m on the other. The station of the beginning of the curve (200m) is 10+000 and its elevation is 228m. 20. Determine the stationing of the lowest point of the curve. Соpy Ctrl + C а. 10 b. 10-zuɔu. 1UTZ09 21. Determine the elevation at station 10+040. a. 227.9c. 226.5 b. 226.7d. 227.1 22. If the uphill edge of the underside of the bridge is at station10+220 and at elevation 229.206m, what is the vertical clearance under the bridge at this point? а. 4.2с. 4.4 b. 4.3d. 4.1
A-3.3% grade meets a +6.6% grade at a vertex (El, 144,37m) directly under an overpass bridge having underside elevation of 156.07 m. A 6.7 meters clearance under the bridge and the center of the curve was observed. Determine the horizontal length of curve in meters.
Sag Curve: A grade from the PVC to the PVI is -6% and from PVI to PVT is +2%. It is required to connect these grade lines with a vertical parabolic curve will pass 3.0 m. directly above the PVI. 11. Determine the length of this curve. a) 420 m b) 380 m c) 400 m d) 300 m 12. Determine the location of the lowest point measured from the PVT. a) 100m b) 75m c) 100m d) 225m 13. Compute the vertical offset at a point on the curve 100m from the PVC. a) 2.45m b) 2.33m c) 1.56m d) 1.33m
Problem 3 A vertical parabolic sag curve of LapuLapu underpass has a grade of -3% followed by a grade of +1.5% intersecting at station 10 +150.60 at elevation 125.00 m above sea level. The change of grade of the sag curve is restricted to 0.5%. 1. Compute the length of curve. 2. Compute the elevation of the lowest point of the curve. 3. Compute the elevation at station 10 + 125.60.
Vertical Curve: If L=1320 ft, the BVC is at 5+00, What is the Station and Elevation for PVI ? G1 is +2.5% and a G2 of -1.5%. Compute the lowest point on the curves elevation and Station.
A -3% grade meets a +5% grade near an underpass. In order to maintain the minimum clearance allowed under the bridge and at the same time introduce a vertical transition curve in the grade line, it is necessary to use a curve that lies 200 m on one side of the vertex of the straight grade and 100 m on the other. The station of PC is 10 + 000 and its elevation is 228 m. Determine the stationing of the lowest point of the curve. A 10+211 B. 10+200 C. 10+106 D. 10+207
In a vertical parabolic curve (g1= +1.1%, g2=-1.7%), length 280 m, fill all below blanks: Rate of change of grade per station: If you know station of PVI (17+66.62), then station of PVC is: (e.g. 12+34.65) If you know elevation of PVT 22.436 m, then the elevation of PVC is: Elevation of station (16+80.00): Station of highest point on the curve: (e.g. 12+34.65) Elevation of highest point on the curve: Station of a point has elevation 22.697 m: