Q1/ A compressor has three inline pistons of mass 40x10 mg, with a crank radius of 0.04 m and ratio n of 4. the crank is equally space in angle and positioned as show. Determine the primary and secondary force and turning moment about the reference plane X when it revolves at 8.33×10 -3 rad/h. KI 120 120 K2 1200 K3 K4 K1= 5 cm, K3= 150mm, K2= 0.1 m, K4= 50 mm

Q1/ A compressor has three inline pistons of mass 40x10 mg, with a crank radius of 0.04 m and ratio n of 4. the crank is equally space in angle and positioned as show. Determine the primary and secondary force and turning moment about the reference plane X when it revolves at 8.33×10 -3 rad/h. KI 120 120 K2 1200 K3 K4 K1= 5 cm, K3= 150mm, K2= 0.1 m, K4= 50 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating masses of the engine have an angular speed of 100 rad/s in clockwise direction when viewed from the front of the car The combined moment of inertia of the rotating masses is 10 kg-m².what is the magnitude of the gyroscopic moment in (N-m)?
The wheel and attached spool have a combined weight of 50 lb and a radius of gyration about its center of kA = 6 in. If pulley B mounted on the engine is subjected to a torque M = 62.5 lb.ft, determine the total work exerted on the system if the pulley has made 9 revolutions. Shipping weight is 280 lbs. 3 in. M 3 in. M 7.5 in. 7.5 in. 4.5 in. 4.5 in.
In a three-joint robot, L1=350mm, L2=250mm and L3=50mm. If x=300mm and Z=400mm and α=30° in two-dimensional space of the gripper, θ1, θ2Find the values of and θ3.
1372. The unbalanced wheel shown in Fig. P-1372 weighs 322 lb and has a maas radius of Kyrstion of 0.866 ft with respect to a horizontal Axin through its gravity center G. At the given instant, w- 3 rad per see and a- 6 rad per oc", both clockwise. If the heel does not alip, determine the value of P which ia directed parallel to the ineline. Ana. P- 251 lb 1373. If the unbalanced wheel described in Prob. 1372 starta from rest when at the posi- tion shown in Fig. P-1372 and does not alip, determine the initial angular neceleration cauned hy a pull P- 24O Ib.
The force F of 250 N is applied because a block with a mass of 20 kg and a radius of inertia of 160 mm as shown in the figure. This force lifts the weight B of 10 kg. Calculate the pulley angular acceleration and the normal acceleration of weight B, tension in the cable and reaction in the pulley bearing.
The following masses m, are located at the given points P₁ : m₁ = 6, P₁(1, −2) m₂ = 5, P₂(3, 4) m3 = 1, P3(−3,−7) m₁ = 4, P₁(6,−1) Find the moments Mx, My, and the x and y-coordinates of the center of mass of the system. Mx My = = I- ▶ x-coordinate of the center of mass: x = y-coordinate of the center of mass: y = B ▶
PLEASE ANSWER IN COMPLETE AND CLEAR SOLUTIONS. INCLUDE NECESSARY FREE-BODY DIAGRAMS. The line of action of force F1 = 377 N is passing through point A(+2,+3,+1) towards B(+5,+5,+4), while that of force F2 = 466 N is through point C(+3,+1, –1) towards D(–2, –3, –4). Use a right-handed coordinate system. a. Determine the moment of force F1 about the origin.b. Determine the moment of force F2 about the origin.c. Determine the magnitude of the resultant moment of forces F1 and F2 about segment OE. Point O is the origin and point E is at (+5,+5,–3).
Each propeller of the twin-screw ship develops a full-speed thrust of F = 330 kN. In maneuvering the ship, one propeller is turning full speed ahead and the other full speed in reverse. What thrust P must each tug exert on the ship to counteract the effect of the ship's propellers? Assume a = 55 m, b = 133 m, c = 18 m. Answer: P = J KN F F
Assuming small displacements, write the equation of motion for the system shown below in terms of x₁, x₂, х1, х2, and 0. Assume that the lever has a mass moment of inertia about the pivot of Im. K₁ 000 M₁ K₂ 000 777 -fa(1) M₂
The bar AB is uniform and has a mass of 50.0 kg. At the moment shown, the rod has an angular velocity of 4.00 rad/s and spring is stretched by 0.30 m. The force constant of the spring is 25.0 N/m.a) Determine whether or not the bar will reach the horizontal position.b) If the bar becomes horizontal, calculate its angular velocity at that position. If not, calculate the angle the bar makes with the horizontal when it comes to rest momentarily.
Determine the resultant and angle of concurrent forces system using algebraic method. F1=P F2=2P F3=P F4=3P F5=1P F6=2P F7=P F8=7P F9=7P 0₁-45 0₂-45 03-70 04=20 05=45 06-45 07-30 08-40 09-20 FA F5 F6 04 05 0₂ 06 F3 0₂ 0, 08 09 F₂ Fg 8 F₂ Fg F₁
Each propeller of the twin-screw ship develops a full-speed thrust of F = 340 kN. In maneuvering the ship, one propeller is turning full speed ahead and the other full speed in reverse. What thrust P must each tug exert on the ship to counteract the effect of the ship's propellers? Assume a = = 44 m, b = 113 m, c = 16 m. 14 Answer: P = i KN F