The rotor of a turbojet engine of an aircraft has a mass 180 kg and polar moment of intertia 10kg.m2 about the rotor axis. The rotor rotates at a constant speed of 1100 rad/s in the clockwisedirection when viewed from the front of the aircraft. The aircraft while flying at a speed of 800km per hour takes a turn with a radius of 1.5 km to the left. The gyroscopic moment exerted bythe rotor on the aircraft structure and the direction of motion of the nose when the aircraftturns, are

Given data; m=180 kgI=10kg/m2ω=1100 rad/s aircraft speed =800km/hrand it takes a turn with a radius…

Answered: km per hour takes a turn with a radius…

km per hour takes a turn with a radius of 1.5 km to the left. The gyroscopic moment exerted by the rotor on the aircraft structure and the direction of motion of the nose when the aircraft turns, are

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Just after the cable becomes taut, which of the following absolute-relative velocity equations is VALID to relate end B and mass center O of disk O?
In a conceptual design, the power to move a bus comes from the energy stored in an onboard rotating flywheel. The flywheel has a mass of 1500 kg, a radius of gyration of 500 mm, and is brought to a maximum speed of 4000 rpm. If the bus starts from rest and acquires a speed of 72 kph at the top of a hill 20 m above the starting position, find the reduced speed of the flywheel. Assume 10% of the energy of the flywheel is lost due to frictional effects. Neglect the energy of the bus contained in the rotation of the wheels. The bus with flywheel is 10,000 kg. H Type here to search ThinkVision Esc @ 2 W F1 # 3 O E $ 4 F3 R % 5 F4 A 6 A F5 28 7 F6 8 F7 ( 9 F8 0 Fe F10 F11 F12 Backspace Prirk Scroon Sys Piq Insert Scroll Lock 00 Home Pause Break Page Up Man Lock 13000 37°F Cloudy (10) F 2:12 PM 4) 11/16/202 Lenovo
A hollow, smooth cylindrical spool has inner radius R/ 2, outer radius R and mass M. The roller is frictionally M mounted so that it can rotate around a fixed horizontal shaft. The mass m is attached to the end of the rope wrapped around the reel. When this mass m is released, it drops by y in time t. The moment of the friction force between the pulley and the shaft, m R/2 7 = R[m(g – 2y/t²) – M(5y/41²)] R/2 prove that it is. (The moment of inertia of a hollow cylinder with inner and outer radi, R1 and R2, with respect to the long axis through the center of mass.)
I need an answer quickly please
Question 1: Consider the system below. At the moment shown, all three blocks are at zero velocity (Fig.1). At the same time a a force (F) of 10N is applied as shown to the grey Black (G). Each block has a mass of 1Kg. Shortly after the force, F, is applied, calculate the following: A. What is the acceleration of the red Block R, with respect to the ground (assume ground is the inertial frame). B. What is the acceleration of the red Block R, with respect to Block B. C. What is the acceleration of the blue Block B, with respect to the inertial Frame (ground). D. What is the acceleration of the grey Block G, with respect to the inertial Frame (ground). E. What should have been the magnitude of force F, such that block R would not move at all with respect to the ground. B 30° G Figure 1: Three-block setup
A Net Torque of 25 Nm is applied to the edge of a flat disc at rest with a mass of 5.00 kg and a radius of 0.50 m. Calculate how many revolutions it will complete before it reaches an angular speed of 10 rpm.
11m 3m 9m A K- 7m What is the mass moment of Inertia about the "A axis" (orange) of a cuboid with cylindrical hole drilled through the centre of a face as shown in the figure. The mass of the cuboid before the hole was drilled M1 = 12kg and after the hole was drilled M2 = 6. 6kg.
Hi, how do you solve this question?
Use four decimal places in your answers please and make it clear.
The figure shows a schematic of a simple Watt governor mechanism with the spindle 0102 rotating at an angular velocity w about a vertical axis. The balls at P and S have equal mass. Assume that there is no friction anywhere and all other components are massless and rigid. The vertical distance between the horizontal plane of rotation of the balls and the pivot O₁ is denoted by h. The value of h = 400 mm at a certain w. If w is doubled, the value of h will be mm. (0) g = 9.8 m/s₂ h Spindle O Q Sleeve (QR) Cylindrical Joint R S
Position vector of a particle of mass m = 5 kg is given by r(t) = 3t³i+5j7t²k. What is its linear momentum at t = 2 s? G = 180i+0j - 140k kg.m/s G = 36i + 5j - 28k kg.m/s O G = 0i+0j + 0k kg.m/s G = 180i+25j - 140k kg.m/s
Consider a toy vehicle with a body of mass M = 2Kg on two wheels, each of mass m = 1Kg and radius r = 0.1 m as shown in the figure. It starts from rest on top of a small hill of height H = 10 m and rolls without slipping. What is the linear velocity of the center of mass at the bottom of the hill? HINT: There is rotational and translational kinetic energy in this problem. Vo = 0 M- Vf M-2K m=lKg molky