Q.2) What is the method of arbitration of the PCI bus? Modify the following diagram arbitration, when there is a device C request use the PCI bus at the same time with device B. The arbiter services the device A then C to transfer 2 data for each, then service device B to transfer 1 data. CLK REOA REQn GNTA GNTB FRAME RDY TRDY Addees Date Addeess Toks AD access-A access D

Q.2) What is the method of arbitration of the PCI bus? Modify the following diagram arbitration, when there is a device C request use the PCI bus at the same time with device B. The arbiter services the device A then C to transfer 2 data for each, then service device B to transfer 1 data. CLK REOA REQn GNTA GNTB FRAME RDY TRDY Addees Date Addeess Toks AD access-A access D

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

draw the curcuit diagram for 4 channel 4 bit multiplexer implemented using 4 channel 1 bit multiplexer. make sure that i need full circuit to save the final multiplexer in the library.
What is not a possible solutions to improve performance ..... of PCM?a. Use of linear PCM codesb. Use of non-linear PCM codes tryc. Use of companded systemsd. Increase number of PCM bits
Draw the circuit diagram of 4-bit Ripple Carry Adder. Page 6 of 8
what is the principle of the of the single arm bridge strain gauge Describe the pin connection and communication principle between devices or MCU by Uart bus
Q5. A general analysis of the switch-mode inverter shown in the figure below is to be done. The switching frequency f,, which is also the frequency of the triangular signal is 1450 Hz. The de voltage, Va, is 600 V. Output voltage is sinusoidal voltage with a frequency equal to 50 Hz. TA ADA. TA- ADA- VAN (Figure 8-4 on page 203 from Mohan's Book) a. Find the frequency modulation ratio, mr. b. Why the frequency modulation is chosen as an integer? c. Calculate the output voltage (rms value of first harmonic), when the amplitude modulation ratio, m., is equal to 0.8. d. Compute the rms values of the 5 most dominant harmonics of v4o at m,=0.8. e. Also indicate the frequencies at these harmonics you have found in part d appear.
The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage source is shown in below figure. Output frequency is 50HZ and the load consists of series R-L components. The load values are 22 and 0.04H, respectively. (Conduction interval for half period is 120°) 150 100 50 T -50 3 -100 -150 .002 .004 .006 .008 .01 .012 .014 .016 .018 .02 Time (sec) a. Calculate and draw the load current for the first two-period interval b. Calculate and draw the load current for the steady-state condition
What is a TTL circuit? What are their main characteristics? (Input voltage and current, output voltage and current, Vcc, …)
The required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired to be designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f & g). 8. gf a b t la Ob d Dp e d8c Dp The 7-segment to be used is of common anode type. Consequently, any segment will be ON if its input is Low, meaning that for displaying 0 the segments inputs (a,b,c,d,e,f.g) should be (0000001), or g will be OFF while all the others are ON. 1- Make a table explaining the inputs and the corresponding outputs for the 6 combinations input (000.101), assuming the other two combinations as don't care. 2- Find the output as a function of the inputs (A,B,C) using K-map to minimize the expressions 3- Show your design using 2-input, and 3-input NAND gates, and inverter.
With necessary diagrams and equations, describe the operations of single-phase half –bridge and full-bridge inverters.
Draw four bit parallel adder circuit diagram.
1. Derive an equation for a 6 to 1 multiplexer. 2. Using the equation in (1), produce a gate network for the multiplexer. Use any gate seen in class.
What are MCBs? Explain the working also?